What a lovely thing to watch! I'd turn the tv off, stick the record player on and fall asleep there.
- Thread starter MattF
- Start date
MattF
Forum Supporter
- Messages
- 18,018
- Location
- South Yorkshire
Primary air is turned down for that photo. Just running on the secondary/tertiary air there. Easier to see the content without larger flames.
Erie Fred
Member
- Messages
- 6,221
- Location
- Erie, Pa USofA
But you have secondary air, so the burn continues farther up, and you are not wasting fuel.
MattF
Forum Supporter
- Messages
- 18,018
- Location
- South Yorkshire
Indeed. I usually only turn the primary down fully last thing though. Nice to see a bit of flame on the logs themselves too. This is a photo with both controls approx. half open.
Occasionally, as in that first photo, it does look much nicer with just the secondary open. It allows a better close-up photo of the firebox with the primary closed though, I think.
Occasionally, as in that first photo, it does look much nicer with just the secondary open. It allows a better close-up photo of the firebox with the primary closed though, I think.
Last edited:
MattF
Forum Supporter
- Messages
- 18,018
- Location
- South Yorkshire
I can honestly say I'm so glad I finally decided to stop being a wuss & suffer the mess & suchlike of getting this fireplace done. I'm still finding dust now from when the work was done, & I still need to do finishing touches on the fireplace, but when you're watching that stove running, it's so worth it. So comfy & calming, just sat here looking at this:
MattF
Forum Supporter
- Messages
- 18,018
- Location
- South Yorkshire
That method is what I've been using with these for starting the fire. Tried a few minor variations. This one seems to work well.
Three in a triangular configuration at the bottom, with a firelighter inbetween them, & one straddled atop them. Leave the bottom ashpan door open until the flue thermometer reaches a certain point, then close that bottom door & let the integrated airflow systems take over.
Saves faffing around with separate kindling.
Barking Mat
Cuddler of hedgehogs.
- Messages
- 13,532
- Location
- France, Brittany.
I manage to halve what you have there.
Just being economical.
I'm currently experimenting with burning pellets in my rayburn.
Biscuit tin with holes in it type affair.
Having mixed results.
MattF
Forum Supporter
- Messages
- 18,018
- Location
- South Yorkshire
Half the fun is figuring out the best way to burn each fuel. Between logs, those other style of briquette & then these, they've all required slightly different technique & airflow settings.
I'm sure you'll figure out the best burn settings for those eventually.
I'm sure you'll figure out the best burn settings for those eventually.
- Messages
- 13,567
- Location
- England
Exactly how I do it.
Usually get it going on a few bit of 'hotmaxx' logs and a couple of bigger ones, then use proper logs.
You can tell a lot from a man's lounge carpet amd the selection of tools in the house. From yours I can tell you are a sensible single man that hasn't got a wife that insists on fully redecorating and recarpeting the house every other year whether it needs it or not.
Haha. I have that bond car somewhere too!
MattF
Forum Supporter
- Messages
- 18,018
- Location
- South Yorkshire
Definitely going to be sticking with briquettes rather than logs, from now on. They burn well, & the door glass alone is a clear indication of how cleanly they burn. All I've done with the glass before lighting the fire today is give it a quick rub with a piece of dry tissue.
With logs, it'd have been a damp cloth dipped into wood ash, for cleaning the glass.
With logs, it'd have been a damp cloth dipped into wood ash, for cleaning the glass.
Barking Mat
Cuddler of hedgehogs.
- Messages
- 13,532
- Location
- France, Brittany.
It's just wood chip under extreme pressure causes it to bind together.
- Messages
- 14,783
- Location
- UK
How long do you cut normal logs at, about 6" enough?
MattF
Forum Supporter
- Messages
- 18,018
- Location
- South Yorkshire
As @Barking Mat said, just chips & dust under pressure.
This Youtube video of the machine he makes is a good insight into the process.
