Tight ‘kin wheel bolts

[Bobupndown]

Same here, but really can't be bothered to do my own stuff now.
Hand start the nut/bolt, wind in with gun just until contact, lower car so wheel is just touching ground then torque up.Don'yt put lower car to ground until wheel cap is on, don't put wheel cap on until wheels are torqued.
I use a smear of oil as I hate copper slip as the stuff always seems to get everywhere...........put a smear on the bolt and somehow its up your arm,in your ear, on the door handle of the car 30ft away.
To the person that has their wheels on and off several times a year, what is wrong with them that they need this so often?, mine are done once a year when its serviced.

Nothing wrong with them at all. Checking brakes, swapping wheels front to rear to even tyre wear cleaning inside of wheels, swapping to and from winter wheels. Just a general car nut tinkering. Had the wheels off my Mini today changing brake fluid and bleeding brakes.

 

[brightspark]

Nothing wrong with them at all. Checking brakes, swapping wheels front to rear to even tyre wear cleaning inside of wheels, swapping to and from winter wheels. Just a general car nut tinkering. Had the wheels off my Mini today changing brake fluid and bleeding brakes.View attachment 345200

thats a bad idea swapping wheels and tires over they get bedded in after a few hundred miles swapping them worn creates less grip only did it once on my stockcar and smashed it up on the 1st bend loosing grip and went strait on always replace tires in pairs as well

 

[God mode restorations]

I looked at those sets, the one I use the most is the 33mm and it’s not in the set You would of thought the clowns that market these would of included that one.

Bob

Yer you would of thought. They left the 33 out so you have to buy it separately. Tossers aint they

 

[Bobupndown]

thats a bad idea swapping wheels and tires over they get bedded in after a few hundred miles swapping them worn creates less grip only did it once on my stockcar and smashed it up on the 1st bend loosing grip and went strait on always replace tires in pairs as well

Never had an issue at sane road speeds. Always keep them on the same side though. Can imagine a tyre going thousands of miles in one direction would benefit from having to go the other way.

 

[nickk]

I tried the copper slip,as an experiment,hasn’t solved it,so will degrease and fit dry,as there’s such mixed opinions,I wonder what the factories do on the assembly line,as that’s where the first liability starts?

 

[Bobupndown]

I would imagine new bolts or nuts, likely with an oily residue from packing, going into newly machined hubs or onto studs would be fitted dry and torqued automatically by the multi bolt tightening machine [probably not the technical term ]

 

[Munkul]

I wonder what the factories do on the assembly line,as that’s where the first liability starts?

Kick the can down the road and say its responsibility of the PDI

 

[God mode restorations]

Yer you would of thought. They left the 33 out so you have to buy it separately. Tossers aint they

I have a bigger set buried in the shed somewhere. Will see if I can dig it out and check sizes

 

[DAPPH]

Yawn. I'm guessing you're the guy who would always come up with 100 reasons why something was a bad idea and never offer any critical thinking or solutions.
Anyway don't worry, i barely touch even my own car with a spanner now

Actually I'm very much a safety first electro mechanical engineer , I got crippled because of unsafe practices that were taught to me in my apprentice days back in 1966 . There was a simple solution but the government refused to supply the £6 bit of gear .


In 1974 I was nominated to go on a course to enable me to promogulate my Units HASAW spent two full days at the H&S place in London near Earls court finding out how to write my units SOP's wrt HASAW. On leaving HMF I undertook a NEEBS course in industrial safety & security . Too many folk get crippled or killed by others acts or omissions .

So long as the idea passes muster to my way of thinking and does not conflict with the makers info or any known legislation I'm all for doing things better & safer in novel ways so long at it is safe . .

Since getting crippled the government have paid me 43 years of 60 % disability war pension currently about £520 a month ... I'd have much rather kept my health and grown my own engineering business instead of being chucked on the scrap heap aged 27 yrs old .

 

[DAPPH]

thats a bad idea swapping wheels and tires over they get bedded in after a few hundred miles swapping them worn creates less grip only did it once on my stockcar and smashed it up on the 1st bend loosing grip and went strait on always replace tires in pairs as well

Several of my motability cars required tyre rotations at set mileage intervals IIRC my old Jimmy , Zaferia and both Kia Sedona's .

Not only replacing tyres in pairs , both Sedona's new tyres had to be the ones specified by KIA and I think put in on the front . They also included rotating the spare wheel .

 

[Barking Mat]

When I was right young I had a diesel Lancia Dedra, and before I gave up on garages, I ended up at a tyre place, they changed the tyres, and put them back on with a dugga dugga, stripping the threads on one or two wheel nuts.

I was young, I was naive, they got the tap set out and in some capacity rectified the problem.

Twenty years later..... I would be going mental with them.

Live and learn.

 

[Barking Mat]

Go on, I'll just add to this...

In the very late 90's I bought a 1963 Commer.

I couldn't get the wheel nuts of of one side, for love nor money.

I had a spider, a very long scaff pole, and an obese female friend.

Well, suffice to say, her bouncing up and down on it, cracked all eight nuts.

But not mine.

Bless her.

Thank you Mc Lucy.

She was from Dunblane, grew up during a dark time.

 

[Moose McAlpine]

Go on, I'll just add to this...

In the very late 90's I bought a 1963 Commer.

I couldn't get the wheel nuts of of one side, for love nor money.

I had a spider, a very long scaff pole, and an obese female friend.

Well, suffice to say, her bouncing up and down on it, cracked all eight nuts.

But not mine.

Bless her.

Thank you Mc Lucy.

She was from Dunblane, grew up during a dark time.

Rightey tightey leftey Lucy?

 

[premmington]

Moving away from the "shall I grease the wheel bolts or not debate".

You next problem if you actually get the bolts out - the spigot! (the wheel stuck on the hub spigot)

I have struggled no resorted to sledge hammering nearly new car wheels off three year old cars.

Rotary wire brush if the are corroded is a must - as they will always get worse.

This is the point where even I am always tempted at a bit of grease.

 

[cheb]

If the manufacturers specified lube on wheel studs they'd have to do that in the factory too. Think of the cost to the shareholders. :deadpan:

 

[Bornfree]

Moving away from the "shall I grease the wheel bolts or not debate".

You next problem if you actually get the bolts out - the spigot! (the wheel stuck on the hub spigot)

I have struggled no resorted to sledge hammering nearly new car wheels off three year old cars.

Rotary wire brush if the are corroded is a must - as they will always get worse.

This is the point where even I am always tempted at a bit of grease.

in the past ive slackened the wheels nuts right off and drove the car up the road.

 

[Bobupndown]

in the past ive slackened the wheels nuts right off and drove the car up the road.

Not a H&S recommended wheel removal technique!

 

[nickk]

in the past ive slackened the wheels nuts right off and drove the car up the road.

I know some garages practicing that.

 

[James1979]

in the past ive slackened the wheels nuts right off and drove the car up the road.

+1

Usually have to sledge lorry and farm ones off. Another reason to add to my list of reasons I hate durabite rims.

Sometimes you can get a portapack ram between the rim and chassis and get them that way. Except poxy aluminium rims

 

[qwakers]

my method..


failed....

this works

take pole,

add car

wheel off and pole....