Screwdriver
Member
- Messages
- 10,740
Crikey. Only 2 hours. A+E looked busy, I waited for as long as I could bear waiting then I figure if it's not that urgent, I'll take it up with my GP and walked out.
- Thread starter Screwdriver
- Start date
Screwdriver
Member
- Messages
- 10,740
Mate, for what its worth, put your feet up and pass this by. No sense in exacerbating a condition with avoidable stress. There'll be other things to turn your hand to. Take care
It's OK, I am not stressed about it. I bent down to set a mousetrap this morning, stood up and my heart went ballistic. SVT they call it and after three more attacks, almost six months of investigation, they found nothing last year (all the way through Xmas '19). Then it stopped (happening!).
I'll get the camera setup and see if I can do a better job of setting up the part in the lathe remembering I am not actually turning anything until I have established the dimensions. Then I might make up a chunk of copper and if I get that far, maybe bang in some weld.
Life's too short.
slim_boy_fat
Member
- Messages
- 29,532
- Location
- Scottish Highlands
Not to sound too brutal, but yours may just turn out to be....
- such things are often referred to as 'warnings' [sincerely hope I'm proved to be wrong 
]
Screwdriver
Member
- Messages
- 10,740
Not to sound too brutal, but yours may just turn out to be....
I think it probably is, for many reasons. Without being a drama queen, I estimate 2-5 years. Get the result of a brain scan soon and will be in a better position to know. A better position to decide if I want to cash in my pension now!
Then it's viva Las Vegas!!
Screwdriver
Member
- Messages
- 10,740
You're lucky I am still bumping into a 15 minute upload restriction. So there's only 15 minutes of this.
The horror, the horror....
The horror, the horror....
Ali
Member
- Messages
- 1,901
- Location
- Cheshire
Yep, rest up a bit, you can still ponder
My Old Landy
Engineering Mayhem
- Messages
- 3,581
- Location
- North Lincs
Cliff hanger or what! How long before you can upload hour long epics?
Screwdriver
Member
- Messages
- 10,740
haha. It was getting late. I am still battling with the tech. I need a remote monitor for the camera.
Little steps. Next thing just tidy up the copper slug and bang in a couple of inches of weld. Watch my shaft turn up like a potato chip.
I guess I have to film it now. And filming any welding is a different kettle of fish. I did buy some cheap and cheerful auto darkening screens from CCP. They didn't work (at all!).
Screwdriver
Member
- Messages
- 10,740
I'm just finishing off a little section I did to finish off this mini series(!).
mtt.tr
Member
- Messages
- 8,461
- Location
- Essex/Suffolk border
The other screw holes on the taper lock are used to remove. No hammer required
Screwdriver
Member
- Messages
- 10,740
I know that obviously. However, since the allen screw didn't want to go down that hole on one occasion, I tapped it off with a copper bonker.
My Old Landy
Engineering Mayhem
- Messages
- 3,581
- Location
- North Lincs
You made a good job of that keyway
Screwdriver
Member
- Messages
- 10,740
Finally!
arther dailey
Member
- Messages
- 6,846
- Location
- England
nice to see the swinden getting used
My Old Landy
Engineering Mayhem
- Messages
- 3,581
- Location
- North Lincs
He should be happy with that
Screwdriver
Member
- Messages
- 10,740
My Old Landy
Engineering Mayhem
- Messages
- 3,581
- Location
- North Lincs
How did it go or has he not tried it yet?Soon find out!
Screwdriver
Member
- Messages
- 10,740
No news is good news.
angellonewolf
Member
- Messages
- 8,771
- Location
- bristol england
come on we all want an update
no news is good news might be its working better than its ever been
no news is good news might be the fix failed as soon as he started it the fix failed the blade went flying bounced off a wall hit the boss working it streight in the chest instantly killed
same out come you would not see him to tell you how it went
Screwdriver
Member
- Messages
- 10,740
Well, he's not dead!
