Stuff you have made today

[Memmeddu]

Built up material on the yesterday demolition thing pin

It had 0.9mm below 0 in some spots
Plus the bushes had worn out as well up to 0.8mm out of tolerance.
So about 2mm of play between parts
Problem is that they need the thing quick, not 90mm induction hardened bar .
So I've had build up material on the middle of the pin so they can use the thing till OEM replacement parts will arrive.
In reality since it's case hardened plus it has been welded it will most likely snap at the first use.
Useless waste of time and 309 electrodes.

 

[Dapph2]

Not made, but modified. My drumming tutor had an old Premier bass drum from the 70s that he wanted shortening by just over 4 inches.

View attachment 517709

First step was to remove all the hardware before moving to the table saw. Set the fence to 4 1/4" so It just removed the holes where the lugs that hold the head on were.

View attachment 517710

To stop the drum sagging and clamping the blade as I rotated the drum I used a few braces.

View attachment 517711

Then I had to remove the inner hoop from the bit I cut off, this was done by setting blade depth to just underneath the depth of the outer shell, move the fence the depth over the blade kerf and repeat.

View attachment 517712

I planed and sanded the last bits of shell from the hoop, then reinstalled it in the shortened drum.

View attachment 517713

Once the glue is cured, probably tomorrow as its soon to be beer O'clock, I'll route a new outer bearing edge on the drum, this is where the drum skin sits, drill a few holes so I can put the lugs back on, reassemble, tune it and it's done. This is a common conversion, makes it easier to transport and you get a punchier sound.

You should have finished your post with BOOM BOOM !

 

[Cheesie]

Something feels off
Where the pilot is supposed to seat?

It will be tight

 

[Memmeddu]

It will be tight

He will be cooked

 

[oldbikedavey]

Yesterday, a rather nice little adaptor bracket to fit an LCD voltmeter to the handlebar of a BSA C.15T -ish thing that lives down in Sarf London.
Thinking about it, it might be worth casting some up, as those voltmeters are proper handy for keeping an eye on battery condition and charging output.
I'm sure that I can make something with a suitably patinated individual finish......

 

[6ply]

I picked up some heavy scrap bar for free a while back. Today I finally tuned it into something useful.

 

[harveyp6]

That's lovely. I can only guess what it is, and even if I did know, I wouldn't have a clue how to use it, but I still like it.

 

[RobCox]

Today I finally tuned it into something useful.

Snap! I made this one back in August. Mine is intended for cutting LH threads using the Ainjest (which only works cutting towards the headstock):

 

[6ply]

Snap! I made this one back in August. Mine is intended for cutting LH threads using the Ainjest (which only works cutting towards the headstock):

View attachment 518055

Very nice. And I see your lathe is a lot cleaner and shinier too! I may make another one sometime, possibly with a wider t slot something like yours as I have plenty of material.

 

[RobCox]

Yesterday I made a couple of table clamp blocks for my mill. The old ones were a bit skinny I thought, though they'd never let go. The old ones are like this:

whereas the new ones grip a bit more of the table:

They needed a few thou dusting off the base to make sure they clamp and don't bottom out. I used the surface grinder for this. Unfortunately the shiny surface revealed this:

That dark line is a crack in the cold rolled stock. I'll never trust it not to fail at some point, so today I made a replacement.

 

[RobCox]

I see your lathe is a lot cleaner and shinier too!

Well, it's only 10 months since I got it and 4 months since I finished a nuts and bolts refurbishment, so I'd hope it would still be shiny!

 

[Hood]

Made a couple of 1.125" wide keys, one steel the other bronze.

Also chopped up 1m of 4" dia 316 into various lengths.

Which I made into rollers, turned down to 100mm dia and lengths of 295mm, 200mm, 195mm and 190mm. Bored out for bearings that are 62mm OD and 17mm thick.

 

[jimbo84]

A little tractor from a mini broken clamp.

Wheels are bronze, steering wheel is a 1p and the seat is a 2p.

 

[Dapph2]

Made a couple of 1.125" wide keys, one steel the other bronze.

View attachment 518068


Also chopped up 1m of 4" dia 316 into various lengths.

View attachment 518069

Which I made into rollers, turned down to 100mm dia and lengths of 295mm, 200mm, 195mm and 190mm. Bored out for bearings that are 62mm OD and 17mm thick.



View attachment 518070

I just hate these dyslexic OCD folk

 

[harveyp6]

I just hate these dyslexic OCD folk

It's CDO if you don't mind. Everybody knows the letters have to be in alphabetical order..........

 

[Hood]

I just hate these dyslexic OCD folk

I certainly can not be accused of OCD, anyone who has seen my workshop will testify to that.

 

[harveyp6]

I certainly can not be accused of OCD, anyone who has seen my workshop will testify to that.

I want proof. Do you offer guided workshop tours?

 

[Hood]

I want proof. Do you offer guided workshop tours?

Just ask @Tangledfeet

 

[RichardM]

I certainly can not be accused of OCD, anyone who has seen my workshop will testify to that.

But do you have a phobia about cleaning?

Do you offer guided workshop tours?

H&S would have a fit - too many trip hazards.

 

[Hood]

But do you have a phobia about cleaning?

Nope, just lazy Really though I prefer chaos and if I tidy I can never find anything

H&S would have a fit - too many trip hazards.

I work on my own so they can't do a thing