Barking Mat
Cuddler of hedgehogs.
- Messages
- 13,479
- Location
- France, Brittany.
Well you won't see air being drawn in as thé glass bowl is on thé bottom.
- Thread starter bert
- Start date
scottmk1
Member
- Messages
- 1,975
- Location
- Scotland
Could ask this lot about their hose
Or try getting this stuff
Or try getting this stuff
Bullet2012
Member
- Messages
- 5,228
- Location
- on average about 200 miles from the ISS.
Or Hyphose
bert
Member
- Messages
- 1,449
- Location
- Wiltshire, England
Just been reading the BSS information and fuel hose with the following is acceptable for the filler pipe work.
Applicability – diesel filling hose in good condition may be accepted without marking or declaration,
provided it can be examined over its entire length. Applicability-hoses marked ISO 7840, ISO 8469, ISO 15540, SAE J 1527, DIN 4798 or RINA DIP/66/96 may be accepted as being suitable for use with petrol or diesel.
I think it's well worth reading everything before I get him back for the recheck.
Applicability – diesel filling hose in good condition may be accepted without marking or declaration,
provided it can be examined over its entire length. Applicability-hoses marked ISO 7840, ISO 8469, ISO 15540, SAE J 1527, DIN 4798 or RINA DIP/66/96 may be accepted as being suitable for use with petrol or diesel.
I think it's well worth reading everything before I get him back for the recheck.
Pete.
Member
- Messages
- 14,956
- Location
- Kent, UK
Try searching for inch and three quarters instead of the Metric size equivalent.
38mm = 1.5"
44mm = 1.75"
51mm = 2"
bert
Member
- Messages
- 1,449
- Location
- Wiltshire, England
Just been checking on the gas system as I managed to borrow a pressure tester. I found the leak and it's on the port they need to do the leak testing 
I'm still fitting a new reg and pigtail but it's good to know none of the appliances are leaking and the system is OK.
I'm still fitting a new reg and pigtail but it's good to know none of the appliances are leaking and the system is OK.
jerrytug
Member
- Messages
- 1,809
- Location
- Isle of Wight
Grandmother/eggs alert..New olives are much safer than PTFE. Or annealed old ones even..my LPG surveyor would give birth if he saw that!
Or is it just a bodge for the gauge pigtail?
Barking Mat
Cuddler of hedgehogs.
- Messages
- 13,479
- Location
- France, Brittany.
bert
Member
- Messages
- 1,449
- Location
- Wiltshire, England
So still not through the BSS but it should do when he comes out next.
Last weekend I did a lot of filler work on the back deck and got it in epoxy primer.
This weekend with the weather being pants I'm inside and doing some woodwork. This area was damaged due to a window leak so the wood was rotten.
Not as much fun as metalwork as you can't weld bits on if you cut it wrong.
Bit more sanding to do before the stain can go on.
Last weekend I did a lot of filler work on the back deck and got it in epoxy primer.
This weekend with the weather being pants I'm inside and doing some woodwork. This area was damaged due to a window leak so the wood was rotten.
Not as much fun as metalwork as you can't weld bits on if you cut it wrong.
Bit more sanding to do before the stain can go on.
Barking Mat
Cuddler of hedgehogs.
- Messages
- 13,479
- Location
- France, Brittany.
Fairplay, that rear deck looks super tidy !
Bullet2012
Member
- Messages
- 5,228
- Location
- on average about 200 miles from the ISS.
Looks great.
has the BSS person found additional faults ?
has the BSS person found additional faults ?
bert
Member
- Messages
- 1,449
- Location
- Wiltshire, England
He found the fridge didn't have the correct fitting on the gas pipe. The tube was pushed onto a flared copper pipe the clipped in place.
It's now got a proper gas hose compression fitting
bert
Member
- Messages
- 1,449
- Location
- Wiltshire, England
Still needs some more work before it can get painted as I missed a few bits that need filling
brightspark
Member
- Messages
- 41,340
- Location
- yarm stockton on tees
measure twice cut once
and a bit of patience 