Brad93
Member
- Messages
- 19,102
- Location
- Essex, United Kingdom
You needed to do a bit of presetting on that
- Thread starter God mode restorations
- Start date
. Nevertheless,the view makes up for it
.
What would you do? I had a 3mm shim about 100mm square at each end,then carver clamped to a 203 UC,should the shim be thicker?
dan.taylor.1
General Tinkererer
- Messages
- 2,786
- Location
- Kendal, Cumbria
If you're still getting 7mm bow with 3mm shims, I'd guess yeah you need more shim. Not sure if it's as simple as adding up the deflections, so 10mm shim? I mean 10mm over 4.1m isn't a huge amount for the weld to pull back.
Brad93
Member
- Messages
- 19,102
- Location
- Essex, United Kingdom
100%
magnet
Member
- Messages
- 1,433
Bit of clock repair. I altered this pendulum suspension hook by cutting a slot in it wih a junior hacksaw.
Its to fit onto the suspension spring in a movement from an old grandmother clock that i got when an old aunt died years back. Its been sitting there waiting for a bit of attention all this time.
The original pendulum had been lost so i had this one that fits the bill so a bit of a mod and the old girl might run again
Its to fit onto the suspension spring in a movement from an old grandmother clock that i got when an old aunt died years back. Its been sitting there waiting for a bit of attention all this time.
The original pendulum had been lost so i had this one that fits the bill so a bit of a mod and the old girl might run again
Barking Mat
Cuddler of hedgehogs.
- Messages
- 13,517
- Location
- France, Brittany.
Looks very similar to the one I bought in error.
Evening all.
So fairly recently a friend spotted this 110 volt Powerfeed for sale second hand on a French equivalent of Gumtree (LeBonCoin), thought of me, phoned me, advertised as from a Bridgeport, and now it's mine. Was about €100.
This photo does not show it complete, there's a fast advance button I've unplugged, to get to the business end, it's missing the cover which should protect the big gear you can see on the left hand end, I can either make or buy one, that's not the issue.
It works, does everything it should, been tested by my mate and me, nice solid cast...
So fairly recently a friend spotted this 110 volt Powerfeed for sale second hand on a French equivalent of Gumtree (LeBonCoin), thought of me, phoned me, advertised as from a Bridgeport, and now it's mine. Was about €100.
This photo does not show it complete, there's a fast advance button I've unplugged, to get to the business end, it's missing the cover which should protect the big gear you can see on the left hand end, I can either make or buy one, that's not the issue.
It works, does everything it should, been tested by my mate and me, nice solid cast...
selectedgrub
Member
- Messages
- 3,477
- Location
- New Zealand
Melvyn Best
Member
- Messages
- 1,836
- Location
- Cambridge
Is that your new ashtray
?
redlig
Member
- Messages
- 4,232
- Location
- wiltshire uk
That is a question you should never ask especially on this forum.How much did it cost you to make?
You do know you can get them for a small donation to charity, usually mounted on a keyring?Daft little thing. It's a dimensionally accurate copy of a pound coin for wifey to put in shopping trolleys
View attachment 503368
Blobber
Forum Supporter
- Messages
- 3,400
- Location
- lincolnshire
Yeah but made in China and all that! British made and proud
Pete.
Member
- Messages
- 14,899
- Location
- Kent, UK
Yeah but made in China and all that! British made and proud
Too right all you gotta do it wait for it to rust now and your life will be complete
- Messages
- 23,486
- Location
- Birmingham
I got a couple when Dominos pizza were giving away goody bags at a local show.
Morris
Member
- Messages
- 1,857
- Location
- Northamptonshire.
I didn't spend a fortune on a lathe just to then take the easy way out
Wifey has knitted hundreds of dog blankets for Battersea and we give to the local air ambulance, we do our bit.
Morris
Member
- Messages
- 1,857
- Location
- Northamptonshire.
The price of a Bantam lathe, tooling, VFD and material.How much did it cost you to make?
Bargain.
