Gragson
Member
- Messages
- 2,558
- Location
- Bucks
- Thread starter monkeymark
- Start date
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 20,147
- Location
- Going Away.
Needed some Coach bolts, so I went to see a friend.
I got by fixings and a bit more.
The bit more.
Wire wool, from course to super fine.
I got by fixings and a bit more.
The bit more.
Wire wool, from course to super fine.
Memmeddu
Member
- Messages
- 5,301
- Location
- Italia Sardegna
Well good to know, I would have saved 600 euro when I've had my punto head gasket fail.Ouch!
View attachment 500575
I got a fat finger on holiday.
View attachment 500576
I went to the urgent treatment hub near me and the very nice nurse took a knife to me and drained a load of gunk out that looked like the mess you get when a head gasket fails
Antibiotics for a week now.
Antibiotics goes in the radiator or in the fuel tank?
Just in case
How are you doing?
Memmeddu
Member
- Messages
- 5,301
- Location
- Italia Sardegna
Better beers out there especially Italian
Memmeddu
Member
- Messages
- 5,301
- Location
- Italia Sardegna
A terrible day
Terrible, I couldn't even breath without sweating.
I'm a summer creature but today was too hot and I've had to weld several things at work.
Fortunately 9% humidity only but it was supposed to rain heavily and would have been even worse
We are not in summer yet.
arther dailey
Member
- Messages
- 6,801
- Location
- England
if the dremel bits are looking for a home...although mine is a chinesium copy it is soo usefull, well done on your haul as ever
Johnnybravo
Member
- Messages
- 3,685
- Location
- Northiam
I was given a sample pack years ago - they were very impressive at cleaning all sorts of crap off my hands.OrderedI'm worth it.
So I bought a big tub . . . I still have a lot of the big tub as they seemed much less effective. I can't get a good enough grip on them to do much. Aldi flogged some a few years ago that seemed to be coated with grit on one side - you could get some traction with those.
OJCar
Member
- Messages
- 2,270
- Location
- Lothian & Westmorland
Or one 300mm thick PTFE washer ...
What do you need that lot for?
Or was it minimum Qty order?
Need 2 per device I'm selling and gotta make 320 devices.Or one 300mm thick PTFE washer ...
What do you need that lot for?
Or was it minimum Qty order?
Was only £80 on AliExpress for custom made
I have absolutely no need for this but congrats on the solution to a problem and then smashing the Kickstarter target
brewdexta
The biggest tool in the box
- Messages
- 5,718
- Location
- UK
The step pulley on the right. It's for the motor swap on the Tom Senior M1 Mill. I was going to bore out the original on the left to 24mm but cutting the keyway in the cast iron pulley with a broach on a fly press is a no go. I do have a hydraulic press resto in progress but it may be a while. The pulley is 7mm shorter than the original but as I'm doubling the motor power from 1 to 2hp and using a VFD, I don't think I will be swapping belts much, if at all, so will align the groove I use most.
brightspark
Member
- Messages
- 41,107
- Location
- yarm stockton on tees
i sold mine for 50 quid and wished i hadnt
OJCar
Member
- Messages
- 2,270
- Location
- Lothian & Westmorland
