Today I acquired...........

[waddycall]

Same model as mine I use it for checking the speed on my stationary engines, it looks like you're missing the extension shaft?

View attachment 431227

Yep, though I might be!

 

[Cuthy246]

I need that space for standing in! It's not a lack of floor area that's the issue, it's floor perimeter, it really needs to go against the wall, and there's no more wall left.

That's not all I acquired today though, I also got a crate of vintage lab crap, including a big burner which definitely has too big an orifice to be used with propane...

There's a couple of smaller ones behind it which are just as bad.

Bunsens typically use natural gas. Get it plumbed into the house

 

[northwest]

Yes,a capable mc from the good old days,@northwest has an improved one even,I’ll get more photos for you when I extract said staircase,covering 50m sq of space!

Yes, it is a Morgan and incredibly useful and versatile. We couldn't be without it.

 

[JOEPRO]

My second M18 fuel angle grinder from faceplant marketplace with a full box of 50x thin cutting discs for £80.



I have had my other m18 grinder for about 5 years now. When welding cars for MOT I end up changing between flap and cutting discs maybe 20 times a day. This will save some time having flap in one grinder and cutting disc in the other. Also allows for one going down for repair if a bearing wears out. (I had to replace the bearings in my other M18 grinder once before easy DIY job which is why I like these grinders alot)

 

[Craig-SM]

My second M18 fuel angle grinder from faceplant marketplace with a full box of 50x thin cutting discs for £80.

View attachment 431266

I have had my other m18 grinder for about 5 years now. When welding cars for MOT I end up changing between flap and cutting discs maybe 20 times a day. This will save some time having flap in one grinder and cutting disc in the other. Also allows for one going down for repair if a bearing wears out. (I had to replace the bearings in my other M18 grinder once before easy DIY job which is why I like these grinders alot)

This will have more power than your previous M18 grinder as I found out and the speed control is always useful

 

[Kram]

Some linear rails. I wasnt planning to cnc anything but it would be useful if I could cut straight lines on plasma etc.. I do have a suitable ballscrew somewhere. Sadly no space for another machine.

Another amazon, a 16" bar and 4 chains for £23 to go on the cs340.

 

[MattF]

Sadly no space for another machine.

Workshop rearrangement time?

 

[JOEPRO]

Square footage! Well not really I just took into sorting out the pile of cr%p laying around my garage. I repurposed a couple of carts to hold car parts. Lots more to do but it's a start anyway

 

[JOEPRO]

I had a second go at this and got more stuff stashed out of the way including a Kompressor engine



Sure the stuff will need wheeled out if I go to remove the car on the lift but its been up there 2 years and counting so doesn't happen very often!

I'll have to buy a 3rd welding trolley now to take up that space that's left.

 

[Onoff]

I'll have to buy a 3rd welding trolley

Buy?

 

[Farside]

One of these arrived the other day...

https://www.amazon.co.uk/dp/B074KQNL2Q

Saves all that tedious farting around trying to drain small engines.

 

[Onoff]

One of these arrived the other day...

https://www.amazon.co.uk/dp/B074KQNL2Q

Saves all that tediou farting around trying to drain small engines.
View attachment 431341

A drop of warm water and you're all set up for a New Year DIY cleanse!

 

[Farside]

A drop of warm water and you're all set up for a New Year DIY cleanse!

With a bit of soap, dear boy.

 

[Onoff]

One of these arrived the other day...

https://www.amazon.co.uk/dp/B074KQNL2Q

Saves all that tedious farting around trying to drain small engines.
View attachment 431341

I use one of those to suck oil through the pipe to the boiler when SWMBO forgets to order heating oil and the pipe fills up with air.

 

[JOEPRO]

Buy?

I will make my own custom welding cart later in 2024. One that can take my MIG, TIG & Plasma cutter + 2no bottles + storage. But no time right now so I ordered a cart from R Tech which will take my Mig and plasma just now and get them off the garage floor.

When I do go to build one I will share ideas on here beforehand.

 

[redlig]

I will make my own custom welding cart later in 2024. One that can take my MIG, TIG & Plasma cutter + 2no bottles + storage. But no time right now so I ordered a cart from R Tech which will take my Mig and plasma just now and get them off the garage floor.

When I do go to build one I will share ideas on here beforehand.

Self propelled might be a good start with all that on board.

 

[JOEPRO]

Self propelled might be a good start with all that on board.

Ye have little faith!

They are all inverter type machines. And 2x 10L bottles would do. I think 30x30 Box section steel frame (40x40 at perimeter and bottles base) with aluminium flooring would do great. The key will be finding nice large strong wheels for it to make it portable over rough concrete in my garages.

It will be made as compact as possible to suit my actual machines.

 

[dobbslc]

Self propelled might be a good start with all that on board.

I think he has a spare V12 Merc lump stashed away...

 

[JOEPRO]

I also finally received my foot pedal for my SIP Tig welder today from Zoro. Only took 3 months!

 

[JOEPRO]

I think he has a spare V12 Merc lump stashed away...

I do have a spare 5L V8, would go well in a welding cart like this