brightspark
Member
- Messages
- 40,989
- Location
- yarm stockton on tees
nooo thought u were going to say 50mm
it gets a bit dodgy if u have bored it out then do it allways wear welding gloves when doing it just in case
- Thread starter daedalusminos
- Start date
it gets a bit dodgy if u have bored it out then do it allways wear welding gloves when doing it just in case
slim_boy_fat
Member
- Messages
- 29,532
- Location
- Scottish Highlands
I don't know which of @brightspark's or @Hood's posts to like since I confess to having used the hacksaw 'hack' on occasion, when my parting tool wasn't speaking to me. 
Luckily I seem to have found one which works atm, so I'm 'safe' again.
So, is the challenge on or not.....?
Luckily I seem to have found one which works atm, so I'm 'safe' again. So, is the challenge on or not.....?
doubleboost
Member
- Messages
- 3,852
- Location
- Newcastle upon Tyne England
I would be up for a bit of speed partingI don't know which of @brightspark's or @Hood's posts to like since I confess to having used the hacksaw 'hack' on occasion, when my parting tool wasn't speaking to me.
So, is the challenge on or not.....?
Hood
I am obsessed.
- Messages
- 17,633
- Location
- Carnoustie, Scotland
No probs from me, give me 5.I don't know which of @brightspark's or @Hood's posts to like since I confess to having used the hacksaw 'hack' on occasion, when my parting tool wasn't speaking to me.
So, is the challenge on or not.....?
Hood
I am obsessed.
- Messages
- 17,633
- Location
- Carnoustie, Scotland
Ok, here is some 55mm Dia, first thing I picked up. Not sure grade but we will say just mild steel. Parting insert is old and likely needing changed soon but still cutting ok.
And I should have cleaned the lens first, vid a bit out of focus
And I should have cleaned the lens first, vid a bit out of focus
I bought one of these from your link - absolutely incredible parting off has become a joy - it was something I USED to dread!
I suppose it helps I have a big old Colchester Triumph so pretty rigid setup.
Ok, here is some 55mm Dia, first thing I picked up. Not sure grade but we will say just mild steel. Parting insert is old and likely needing changed soon but still cutting ok.
And I should have cleaned the lens first, vid a bit out of focus
You are braver than me - i run half the speed and half the feed you do
bletchmonster
Member
- Messages
- 698
- Location
- Cheshire. England.
Another one here that bought on the strength of Hoods recommendations. I run it at the lower end of its suggested feed/speed and I'm stunned with the ease it chomps stuff off.
Hood
I am obsessed.
- Messages
- 17,633
- Location
- Carnoustie, Scotland
Behave man, I wasn't even tryingYou are braver than me - i run half the speed and half the feed you do
Hood
I am obsessed.
- Messages
- 17,633
- Location
- Carnoustie, Scotland
The Iscar tangentials are the best I have ever used and I have used most of the known brands from Sandvik, Kennametal, etc etc.
I often wonder if my struggle to get a good finish turning steel is down to worn bearings or something but it can't be as I can part off all day long no problems at all.
Using one of these parting tools it is effortless.
I suppose parting off will show up chatter and wear more than anything else?
Hood
I am obsessed.
- Messages
- 17,633
- Location
- Carnoustie, Scotland
You mean to the Iscar Tang grip?
If so then you will have to wait until next month as MSC have it on special every second month, blade and 10 inserts for about £82 plus VAT.
slim_boy_fat
Member
- Messages
- 29,532
- Location
- Scottish Highlands
Over to you, @brightspark
Woody.v8
Blue gluer
- Messages
- 4,205
- Location
- staffs
He will be busy mounting his rapador to his cross slideOver to you, @brightspark
brightspark
Member
- Messages
- 40,989
- Location
- yarm stockton on tees
hmmmmm ok il admit defeat on that oneOk, here is some 55mm Dia, first thing I picked up. Not sure grade but we will say just mild steel. Parting insert is old and likely needing changed soon but still cutting ok.
And I should have cleaned the lens first, vid a bit out of focus
im man enough to didnt speed that vi d up though did you
Hood
I am obsessed.
- Messages
- 17,633
- Location
- Carnoustie, Scotland
... didnt speed that vi d up though did you
I can send you the original direct from the phone if you wish
brightspark
Member
- Messages
- 40,989
- Location
- yarm stockton on tees
no need just winding you upI can send you the original direct from the phone if you wish
123hotchef
Member
- Messages
- 14,318
- Location
- Kent
yes please can we have the link again? I dont have much luck with parting tools/inserts
