- Thread starter monkeymark
- Start date
DAPPH
as dyslexik as I'm daft
- Messages
- 7,489
- Location
- Near to Cross Hands Llanelli SouthWales GB
I still have my Casio fx-39 from 1979 it seemed to cost a lot back then so i kept it for years and retired it to a box in the loft.
this is one
In 1964 my brother spent a two months wages £76 IIRC on getting one of the new fangled Sinclair six digit red LED calculators that took four or six AAA batteries and needed a new set a couple of hours late . Even the one shown above looks a long way off in the future , what sort of price was if ( if you can remember ) ? I was learning how to use a slide rule & still have one with the instruction & plastic storage case .
Last edited:
DAPPH
as dyslexik as I'm daft
- Messages
- 7,489
- Location
- Near to Cross Hands Llanelli SouthWales GB
Richie before you start it ….lube the cylinder with the spark plug out ..give it several pull overs and squirt a bit of WD 40 in between pulls. Done so it lubes the piston rings & the cylinder wall and piston skirt . Other wise if it's too dry .....the rings might break or pick up metal from the walls & knacker the machine .
PS Your'e a jammy git finding such a score . They are brilliant machines if looked after .
Cheers Dapph,
I've got it running. There's a thread in the projects section with a little video. It always turned over very smoothly by hand before I had it under power. I got it running properly since the video with fuel in the tank.
Rich
DAPPH
as dyslexik as I'm daft
- Messages
- 7,489
- Location
- Near to Cross Hands Llanelli SouthWales GB
For my HNC electrical engineering I was horrified to discover an hour or so before the exams that I'd lost or had my Cassio scientific calculator nicked ( colleges tend to have some nice folks like that ).
So I went to the college shop and purchased a new calculator …. Arragh I couldn't work it for toffee . I managed to jam it up on anything but simple multiplications. Sat and worked things out long hand instead & didn't do as good as I'd hoped as I didn't finish the first paper .
So a rule for life was developed by me :- never change your calculator to a snazzier one if you are about to do important exams , treat your current calculator like a bar of gold .
DAPPH
as dyslexik as I'm daft
- Messages
- 7,489
- Location
- Near to Cross Hands Llanelli SouthWales GB
My evil brother who became a copper , bet me I could not pee over the single strand of wire running round the cattle field . As a result though I'm led to believe Mum & Dad were married before he was born ..... I do have my doubts .
Used to do this for a laugh when we were kids (many moons ago) we had a a line of 4 or 5 of us the strange thing was only the the one touching the fence and the last one in the line got the shock.
qwakers
Member
- Messages
- 2,498
- Location
- cornwall, united kingdom
cant think of a better place to put this and it doesnt rate its own project thread, so ill put this here...todays half of yesterdays post
its working fine just need a but of fettling.
spent the day intermittently fiddling with the tyre machine.
first job was to fix the auto oiler and get rid of (most of) the air leaks. ended up totally re plumbing the air system.
then i practiced taking tyres off. not the hardest thing to learn, but i did have to watch a google vid to get my head round it....
i also discovered putting tyres back on is easy
i then sorted out the air switch that raises and lowers the assist arms. and found that doesn't half make life easier!
i took the valve apart and found the lower and raise arm had a fitting that was almost all the way undone. screwed it back together which effectively shortened the arm and it works fine.
i also made and fitted a side panel to the machine to close off the gaping hole in the side.
i used a air hammer to remove the sliding roller that you use to hold the tyre off the bead and cleaned all the rust off it so now it slides nicely.
i was then going to drill a hole in the end to put a bolt down with a large washer to prevent it travelling past its endpoint but although i have a very cool fully adjustable radial pillar drill,
i only had a cheap chinese vice dad bought for xmas last year, and, well... they don't last long it seems.
also mocked up a power supply for the balancer and found that there appears to be nothing wrong with it. i do need a users manual for it though...
just have to mount that neatly now and wire it properly and that will be good to go too.
oh, and on a only slightly related subject. ...
i went to lend my pressure washer to dad last week, so i dragged it out of the shed, chucked it in the car and took it over. started it up and ....
not fixing that in a hurry.
now as it happens they have a identical (ish) pressure washer that they've never got round to fixing, so i nicked the carb off mine and the pressure hose lance etc and swapped it over. so now my parents have a pressure washer, but i don't. which is a shame, as id REALLY like to clean the tyre machine off....
indy4x
Forum Supporter
- Messages
- 3,529
- Location
- Pontypool, South Wales. UK
This came up cheap , it's originally from a well know DIY store compound, heavy duty security fencing with posts, 2 large gates and smaller, they sold it off when closing down and its been sat unused since. Its also galved and powder coated so should outlast me
Social distancing observed which meant it was a complete PITA to load on the trailer by myself
Social distancing observed which meant it was a complete PITA to load on the trailer by myself
brewdexta
The biggest tool in the box
- Messages
- 5,775
- Location
- UK
I've been a very naughty boy, but I'm worth it 
Its an 18v router, no battery, but comes with a trim and plunge bases, fences etc.
The body itself is quite small
I've used it already for a small job however I need to wait for some guide bushes and cutters for the Leigh dovetail jig to be delivered before it gets a lot more use. The intention is to use my Dewalt corded for the tails, and the Milwaukee for the pins, that way I don't have to keep swapping cutters. I have depth jig to help set the cutter depth but they always differ slightly when changing cutters meaning either a tight or sloppy dovetail and much messing about. This way once set up correctly I can breeze through all 40+ dovetailed drawers and trays for the kitchen without fiddling about.
This is my second Milwaukee 18v Fuel router. The other one is sat in a work colleague's desk in Chicago waiting for the next time somebody comes over to the UK. That may be a while so will probably sell that to another US work colleague.
Cheers
Andy
Its an 18v router, no battery, but comes with a trim and plunge bases, fences etc.
The body itself is quite small
I've used it already for a small job however I need to wait for some guide bushes and cutters for the Leigh dovetail jig to be delivered before it gets a lot more use. The intention is to use my Dewalt corded for the tails, and the Milwaukee for the pins, that way I don't have to keep swapping cutters. I have depth jig to help set the cutter depth but they always differ slightly when changing cutters meaning either a tight or sloppy dovetail and much messing about. This way once set up correctly I can breeze through all 40+ dovetailed drawers and trays for the kitchen without fiddling about.
This is my second Milwaukee 18v Fuel router. The other one is sat in a work colleague's desk in Chicago waiting for the next time somebody comes over to the UK. That may be a while so will probably sell that to another US work colleague.
Cheers
Andy
Olderisbetter
Member
- Messages
- 3,936
- Location
- Wolverhampton
I am unsure but i bet it could have been a weeks wages as i remember him saying he was happy i was good at maths but i cost more to put through education than my 3 sisters all put together.
steviec_lj
Rust Welding Professional
- Messages
- 2,803
- Location
- Barnetby, N.Lincs
Like the look of that..I've been a very naughty boy, but I'm worth it
View attachment 222520
Its an 18v router, no battery, but comes with a trim and plunge bases, fences etc.
View attachment 222522
The body itself is quite small
View attachment 222521
I've used it already for a small job however I need to wait for some guide bushes and cutters for the Leigh dovetail jig to be delivered before it gets a lot more use. The intention is to use my Dewalt corded for the tails, and the Milwaukee for the pins, that way I don't have to keep swapping cutters. I have depth jig to help set the cutter depth but they always differ slightly when changing cutters meaning either a tight or sloppy dovetail and much messing about. This way once set up correctly I can breeze through all 40+ dovetailed drawers and trays for the kitchen without fiddling about.
This is my second Milwaukee 18v Fuel router. The other one is sat in a work colleague's desk in Chicago waiting for the next time somebody comes over to the UK. That may be a while so will probably sell that to another US work colleague.
Cheers
Andy
slim_boy_fat
Member
- Messages
- 29,508
- Location
- Scottish Highlands
Today I acquired, a do-it-yourself haircut just to tidy things up a bit. Looks like I've been redacted....
Dcal
Member
- Messages
- 4,070
- Location
- Antrim Northern Ireland
Today I acquired, a do-it-yourself haircut just to tidy things up a bit. Looks like I've been redacted....
View attachment 222533
Is that duck tape?
Kinky
slim_boy_fat
Member
- Messages
- 29,508
- Location
- Scottish Highlands
stuvy
Member
- Messages
- 9,304
That'd be far too sticky.
he only found that out when he tried to remove it
he now looks surprised
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 20,326
- Location
- Going Away.
A few gifts from the nice neighbour.
Yes, it does work. Not a bad item.
Dam good set of ear defenders.
As good as my RN Gun Duffs.
Yes, it does work. Not a bad item.
Dam good set of ear defenders.
As good as my RN Gun Duffs.
God mode restorations
Member
- Messages
- 8,149
- Location
- uk colchester
I like that...that's niceHaving a tidy of the garage: centres from the old Turning cell at Cessna Fluid Power in Glenrothes, I picked it up when the factory closed with some other tools and found it at the back of a shelf:
Craig-SM
Member
- Messages
- 2,134
- Location
- Heckmondwike
I've been a very naughty boy, but I'm worth it
View attachment 222520
Its an 18v router, no battery, but comes with a trim and plunge bases, fences etc.
View attachment 222522
The body itself is quite small
View attachment 222521
I've used it already for a small job however I need to wait for some guide bushes and cutters for the Leigh dovetail jig to be delivered before it gets a lot more use. The intention is to use my Dewalt corded for the tails, and the Milwaukee for the pins, that way I don't have to keep swapping cutters. I have depth jig to help set the cutter depth but they always differ slightly when changing cutters meaning either a tight or sloppy dovetail and much messing about. This way once set up correctly I can breeze through all 40+ dovetailed drawers and trays for the kitchen without fiddling about.
This is my second Milwaukee 18v Fuel router. The other one is sat in a work colleague's desk in Chicago waiting for the next time somebody comes over to the UK. That may be a while so will probably sell that to another US work colleague.
Cheers
Andy
It’s on my list but the U.K. prices are unrealistic although they are dropping at the moment and I’ve seen them for £265.
