Review Vevor 1 Ton Arbor Press

[Kram]

Ordered one of these for £46. The plan is to use it for breaking and riveting chainsaw chains with less noise than smashing a punch with a club hammer.

https://www.amazon.co.uk/dp/B0CGJ4QT17

I'll do a review later in the week.

 

[MattF]

I can never decide whether to like or hate you. Just ordered one. For that price, it'd have to be really naff not to be worth its cost, & a handy thing to have around for quick pressing operations.

 

[not done it yet]

Vevor tonnes are very likely just like other chinese specs -severely over-stated.

 

[skotl]

I can never decide whether to like or hate you. Just ordered one. For that price, it'd have to be really naff not to be worth its cost, & a handy thing to have around for quick pressing operations.

 

[Farside]

I vill resisssst.

 

[Agroshield]

Vevor tonnes...

It is a mechanical press. It is the same shape, size and mechanical arrangement (mechanical advantage) as every other one sold to the same specifications.

Thus, when the same arm force is applied to its operating lever, there would have to be some special area of physics, yet undiscovered by mankind, for it not to produce the same force as others in the same class.

You can argue about build quality and longevity of overseas-made items, but in this case, it is difficult to see how the applied force could be less.

 

[oldbikedavey]

Ordered one of these for £46. The plan is to use it for breaking and riveting chainsaw chains with less noise than smashing a punch with a club hammer.

https://www.amazon.co.uk/dp/B0CGJ4QT17

I'll do a review later in the week.

A Renold type chain breaker isn't available ?

 

[MattF]

A Renold type chain breaker isn't available ?

That's limited in purpose. An arbor press, less so.

 

[not done it yet]

It is a mechanical press. It is the same shape, size and mechanical arrangement (mechanical advantage) as every other one sold to the same specifications.

Thus, when the same arm force is applied to its operating lever, there would have to be some special area of physics, yet undiscovered by mankind, for it not to produce the same force as others in the same class.

You can argue about build quality and longevity of overseas-made items, but in this case, it is difficult to see how the applied force could be less.

Agreee, but they seem to manage to sell them cheap for a variety of reasons, poor casting, not quite straight, poor alignment, etc. Likely OK for the application quoted but perhaps fall down on other operations. Pot luck, IMO, if it is a full spec example of that generic piece of kit.

 

[Kram]

Its a reasonable amount cheaper than the proper tool for chain breaking and I think it should be more capable.

https://www.amazon.co.uk/Oregon-24548B-Bench-Chain-Breaker/dp/B00XJOY0PK/

A Renold type chain breaker isn't available ?

Unsure if that will work on chainsaw chains, particually if intending to reuse the links - 1/4" pitch links are not available to buy.

 

[oldbikedavey]

Its a reasonable amount cheaper than the proper tool for chain breaking and I think it should be more capable.

https://www.amazon.co.uk/Oregon-24548B-Bench-Chain-Breaker/dp/B00XJOY0PK/

Unsure if that will work on chainsaw chains, particually if intending to reuse the links - 1/4" pitch links are not available to buy.

1/4" pitch sounds a bit tiddly for anything..
How do you intend to re-use the extracted links ?
Wouldn't fancy a saw-chain going awry at full belt , that's for sure...

 

[Kram]

Reassemble the links and hit with hammer to swage the pins back out.

1/4" pitch is only used on small saws like my climbing saw Echo 2511, its not that powerful.
For the bigger .325 and 3/8" chains I would normally use new links. However the new .325 link pins I got, that I use for my big saw, are just a bit too long and hammer wont get them down enough, so the last 4 chains I did with reused links. I dont think theres any chance of them coming off.

 

[Gragson]

This post has reminded me to drag out a No3 I got ages ago from MOL which I could have used a fair few times if I remembered I had it!



Need to drill out broken tooling retaining bolt at base of rack which should be straightforward.
Question tho, can you get "sets" of popular press tooling for these? Appreciate fit for No1 is probably smaller than a 3 but my googlefu is failing me as I can't find any. Also appreciate you would need to make thngs specific for other jobs but just wondered on usual job sets?
Also it would *iss @MattF off with more things to buy

 

[8ob]

Also appreciate you would need to make thngs specific for other jobs but just wondered on usual job sets?
Also it would *iss @MattF off with more things to buy

I am converting/adapting one of these small presses into a valve spring poundage/height checker, it’s going to be chopped about a bit too much to be any good for anything else but at £50 it’s no hardship.

 

[MattF]

What's the general quality of the press like @8ob?

 

[Kram]

Tried it today, cant complain about the quality however I have not used one before so dont have anything to compare with. However I have used industrial hydraulic presses, much simpler. Had to find spacers to get handle in a good position.

For punching out chain links, it could really use an extension handle, I am leaning in it! I cant believe thats 1 ton of force. @8ob if thats a presure gauge in your pic, it would be interesting what it reads at various amounts of effort.

I did notice, compared with club hammer, that when the link lets go, the press has a habit of bending the link, too much force, where a club is only just breaking the link and often another hit to push it free. Perhaps I could add a stop so that it is only pushing a couple millimeters.

I did have to turn down the chinese punch set from 10.6mm to 10mm. They appear to be a decent grade of hard chromed steel, reminds me of 709m40. Ignore the rubbish finish as I left the cutter in while going back

 

[MattF]

the press has a habit of bending the link, too much force, where a club is only just breaking the link and often another hit to push it free. Perhaps I could add a stop so that it is only pushing a couple millimeters.

Use a straight instead of tapered punch?

 

[ukracer]

This post has reminded me to drag out a No3 I got ages ago from MOL which I could have used a fair few times if I remembered I had it!

View attachment 467284

Need to drill out broken tooling retaining bolt at base of rack which should be straightforward.
Question tho, can you get "sets" of popular press tooling for these? Appreciate fit for No1 is probably smaller than a 3 but my googlefu is failing me as I can't find any. Also appreciate you would need to make thngs specific for other jobs but just wondered on usual job sets?
Also it would *iss @MattF off with more things to buy

It's a shame they don't do these on vevor.

 

[Misterg]

Had to find spacers to get handle in a good position.

13:57 on here:

 

[Gragson]

I did have to turn down the chinese punch set from 10.6mm to 10mm.

I am guessing my No3 is a generic larger one than the 1, tooling insert aperture on mine is smidge over 1/2" and all the bolts on it are 5/16 UNC.
I've ordered some 1/2" silver steel round bar to make some tooling / punches, and 5/16 retainer bolts. Saying in case there is a bit of a mix of imperial and metric? on the No 1

13:57 on here:

Good one cheers definitely looking at that rack mod to do, I don't have that shim plate in mine at the head so might take a look at that although its not that wobbly as a press tool.

It's a shame they don't do these on vevor.

No 3 - https://uk.vevor.com/arbor-presses-...le&utm_term=&utm_skip=google_one_tap_status_1

No 1 - https://uk.vevor.com/arbor-presses-...r-mountable-bearings-cast-iron-p_010205073857