Blobber
Forum Supporter
- Messages
- 3,380
- Location
- lincolnshire
What have you done to the poor boys fingers?!
- Thread starter monkeymark
- Start date
Onoff
In the land of the unfinished project I am King!
- Messages
- 12,966
- Location
- Sevenoaks, UK
After seeing them recommended on here I bought a pair of the Piergiacomi flush cutters on Amazon.
View attachment 370275
I went for a larger set as they can cut 2.5mm & were on offer. Unfortunately the 2 cutting edges don't meet properly with one edge sliding over the other when squeezed hard.
View attachment 370276
So they are heading back to Amazon for replacement.
How do they get away with selling what must a lot of the time be fakes, touted at full price? Brother just bought some plastic faced pliers for forming 0.7mm copper. Broke first try. Look at the light/dark colours at the break. From Amazon again.
Morning!
Question for the forum:
I have been offered taps in inch sizes where only the diameter value is given, but no indication of the pitch.
Is there a standard correlation between diameter and pitch in inches if any additional information is missing or do I at least have to know the system (BSW, UNC, UNF, etc.)?
These are the sizes: 1-3/8", 1-1/2", 1", 7/8", 7/8" Pipe, 3/4" - the pictures look like pretty fine thread to me, may be the size is deceiving though ...
View attachment 370290
Thank you.
Carsten
--
I think the "G" denotes BSP thread.
Onoff
In the land of the unfinished project I am King!
- Messages
- 12,966
- Location
- Sevenoaks, UK
25.4_mechanic
Member
- Messages
- 1,046
- Location
- Germany, southwest
Thank you. Then I'm already smarter about one of the specimens.
With the designation Pipe, it should be similarly defining, but in sealing?!?
What is the situation with the unmarked ones?
Thanks,
Carsten
--
Brad93
Member
- Messages
- 19,098
- Location
- Essex, United Kingdom
They're BSP / Pipe Thread
Question for the forum:
I have been offered taps in inch sizes where only the diameter value is given, but no indication of the pitch.
Is there a standard correlation between diameter and pitch in inches if any additional information is missing or do I at least have to know the system (BSW, UNC, UNF, etc.)?
These are the sizes: 1-3/8", 1-1/2", 1", 7/8", 7/8" Pipe, 3/4" - the pictures look like pretty fine thread to me, may be the size is deceiving though ...
View attachment 370290
Thank you.
Carsten
--
As indicated by the G
25.4_mechanic
Member
- Messages
- 1,046
- Location
- Germany, southwest
As have my
UNC, UNF, 4-42V don't have that. So that's a clue.
We have that established. Thank you all.
What about the unmarked ones?
Carsten
--
25.4_mechanic
Member
- Messages
- 1,046
- Location
- Germany, southwest
I asked the supplier: Some of the taps have marks like S, R, SS - does that mean anything?
When I have bought them I will surely do that, but I wanted to know what it is first .... the guy does want money for them, you know
Carsten
--
25.4_mechanic
Member
- Messages
- 1,046
- Location
- Germany, southwest
That could be a problem, for me it's not much more than a "nice to have", the guy thinks he has quite the good stuff - I didn't wanted to open his eyes unneccessary
Carsten
--
MattF
Forum Supporter
- Messages
- 17,891
- Location
- South Yorkshire
I've the exact same for 6yrs plus, I call it metalworker, used for wood a few times but mostly metal, very hard to stall, versatile bit of kit with the right belts and pads
Good to know. I bought some medium & fine belts, and some mixed grit packs of discs too.
As I understand it the EU has adopted BSP thread sizes for pipe threads so they directly equate to your 'G' threads, (though the 'G' on your taps probably actually relates to GAS as they probably pre-date the EU adoption).That could be a problem, for me it's not much more than a "nice to have", the guy thinks he has quite the good stuff - I didn't wanted to open his eyes unneccessary
Carsten
--
I'm working from old knowledge of older British Standards, so I may be a little out of date.
"G" was under BS2779 - parallel female thread - so the tap marked with a "G" would create a female parallel thread.
What confuses me is your SKF tap with the "R" designation - the "R" indicates a male taper thread to BS21 - which obviously the tap isn't going to create . . .
Rc - female taper thread under BS21. Rp - parallel female. Rs parallel male. RL also parallel male (long)
BS2779 is for joints where the seal is not made on the thread, BS21 is the same as one of the ISO standards for seals on the thread.
I have to admit for a decade I simply slapped "Tap **BSP" or thread "** BSP" on drawings, and never had a problem - things came in, or were made, things screwed in, on or together, and simply worked, even up to silly pressues.
Moved companies were internal standards required the use of "Rc", "G" etc and I constantly had calls from suppliers asking what I meant . . . so I now add "(BSP)" and the calls stopped
Seadog
Save the planet. It's the only one with rum!
- Messages
- 12,939
- Location
- NE London - UK
The German DIN standard I'm certain is BSP.
Gragson
Member
- Messages
- 2,637
- Location
- Bucks
Having a chat with me neighbour over the fence today like you do.., he's quite new, only been there 5 years anyway, good bloke ex facility maintenance and been doing a load of work on his patch.
Anyway, starts going on about our rear borders which back onto a fairly large pathway with a downsloping embankment behind our fences.
Long one short, says our fences are 10ft back from where they should be because of the incline down to the pathway - we own that 10ft beyond the back fence he says!
Checked the land registry transfer deeds and he's bloody right! so today I acquired 300sq feet
Made the mistake of telling the Mrs, seems to be calculating some back breaking plans....should have kept me gob shut, its a bloody jungle on the other side
anyway, good bloke ex facility maintenance and been doing a load of work on his patch.Anyway, starts going on about our rear borders which back onto a fairly large pathway with a downsloping embankment behind our fences.
Long one short, says our fences are 10ft back from where they should be because of the incline down to the pathway - we own that 10ft beyond the back fence he says!
Checked the land registry transfer deeds and he's bloody right! so today I acquired 300sq feet
Made the mistake of telling the Mrs, seems to be calculating some back breaking plans....should have kept me gob shut, its a bloody jungle on the other side
25.4_mechanic
Member
- Messages
- 1,046
- Location
- Germany, southwest
Today I have acquired a much better tidied garden and space for bulbs and garlic to be planted for next spring's harvest.
With the Holder_A28 narrow-gauge tractor with Celli spade machine we were pretty fast.
(The Holder_A28/Ferrari 95 deserves to be discussed in this thread too - four equally sized driven wheels - still need to do it).
Really nice, such a spade machine:
spade handles (four of them in our case) are driven by a large crankshaft and guided by horizontal arms in an asymmetrical path, driving their spade blades vertically into the soil, whereupon the picked-up soil is thrown against the sheet metal at the back and then distributed.
In contrast to tilling, the soil can be as wet as it wants, you just have to be able to drive. The soil treated in this way dries much faster, of course. This type of soil cultivation is considered the gentlest, far better than ploughing, for example.
This method is not very common or even known here, but I know that those Dutch, who are punished with particularly wet soils, only get yield out of their fields in this way - and when it comes to making or not making an Euro for a Dutchman, he gets resourceful.
Where we still want to plant onions and garlic before the winter, we will of course have to work the soil this year, for the rest we hope for a few days of frost, which will break up all the clods finely.
In spring, when it has dried up, we can then start tilling directly and get fantastic soil again ....
Chard, mustard greens and ruccola have been particularly good to us this year and are constantly sprouting. Today we were able to take some baskets of fresh vegetables with us (mmhhh, how am I going to explain to the Scots here what I'm talking about ... Vegetables ... hhmmm?).
Today we have acquired a nice afternoon outdoors
Carsten
--
With the Holder_A28 narrow-gauge tractor with Celli spade machine we were pretty fast.
(The Holder_A28/Ferrari 95 deserves to be discussed in this thread too - four equally sized driven wheels - still need to do it).
Really nice, such a spade machine:
spade handles (four of them in our case) are driven by a large crankshaft and guided by horizontal arms in an asymmetrical path, driving their spade blades vertically into the soil, whereupon the picked-up soil is thrown against the sheet metal at the back and then distributed.
In contrast to tilling, the soil can be as wet as it wants, you just have to be able to drive. The soil treated in this way dries much faster, of course. This type of soil cultivation is considered the gentlest, far better than ploughing, for example.
This method is not very common or even known here, but I know that those Dutch, who are punished with particularly wet soils, only get yield out of their fields in this way - and when it comes to making or not making an Euro for a Dutchman, he gets resourceful.
Where we still want to plant onions and garlic before the winter, we will of course have to work the soil this year, for the rest we hope for a few days of frost, which will break up all the clods finely.
In spring, when it has dried up, we can then start tilling directly and get fantastic soil again ....
Chard, mustard greens and ruccola have been particularly good to us this year and are constantly sprouting. Today we were able to take some baskets of fresh vegetables with us (mmhhh, how am I going to explain to the Scots here what I'm talking about ... Vegetables ... hhmmm?).
Today we have acquired a nice afternoon outdoors
Carsten
--
