- Thread starter God mode restorations
- Start date
MattF
Forum Supporter
- Messages
- 17,625
- Location
- South Yorkshire
Have you been chopping up a massive floater?
Wonder how many of us thought log-chopper straight away? That was my first thought too. 
redlig
Member
- Messages
- 4,159
- Location
- wiltshire uk
Nothing so exotic.Have you been chopping up a massive floater?
In any case i resort to Marigolds and the bread knife.
CaptainPugwash
Member
- Messages
- 107
- Location
- North West England
Moving/ hooking onto a slipped roof tile or fascia or something?
I'm befuddled
I'm befuddled
redlig
Member
- Messages
- 4,159
- Location
- wiltshire uk
automobile involved.
selectedgrub
Member
- Messages
- 3,430
- Location
- New Zealand
Breaking into cars.
redlig
Member
- Messages
- 4,159
- Location
- wiltshire uk
Very close !
Had a flattening of battery and in the process of swapping for a good one "somehow" ended up with being locked out with the bonnet closed but the O/S passenger window open enough to force arm thro. Tool made to reach bonnet release handle . String was to retrieve stick in event of dropping inside car due to ageing fumbly fingers.
Melvyn Best
Member
- Messages
- 1,801
- Location
- Cambridge
What’s wrong with a tyre lever??
redlig
Member
- Messages
- 4,159
- Location
- wiltshire uk
What’s wrong with a tyre lever??
If you think I'm going to sacrifice a tyre lever to clear that think again. A guy has standards!!
My Old Landy
Engineering Mayhem
- Messages
- 3,573
- Location
- North Lincs
Made a few hats for tomorrow's craft fair. They sell quite well for us. It's not really a core thing for us but we get asked for them. Since starting doing them we have sold over 40!
Do you stitch the leather tabs on or just laser them in position pre stitched on.
My Old Landy
Engineering Mayhem
- Messages
- 3,573
- Location
- North Lincs
They are heat activated glued on. I laser them flat and use a Circuit hat iron to attach them.
Gragson
Member
- Messages
- 2,594
- Location
- Bucks
Chap on another forum makes these rifle butt things, and at a reasonable price.
But not usually in brass and I like shiny
Made some ply templates, cut on the Femi, then some careful shaping.
Bit of polishing, cut some NBR sheet for the pad & Evostick on, will put some caps on for the screw holes.
Pleased how it's turned out, and quite nice to shoot off a tripod.
But not usually in brass and I like shiny
Made some ply templates, cut on the Femi, then some careful shaping.
Bit of polishing, cut some NBR sheet for the pad & Evostick on, will put some caps on for the screw holes.
Pleased how it's turned out, and quite nice to shoot off a tripod.
MattF
Forum Supporter
- Messages
- 17,625
- Location
- South Yorkshire
Brass always makes a good addition.
MattF
Forum Supporter
- Messages
- 17,625
- Location
- South Yorkshire
Added an undershelf to that bench extension I made for the 3D printer. Ordered a couple of these, the other day:
so that I can pop a monitor on the front of the bench, & the second was in order to use the bracket under the shelf so that I can stash the monitor out of the way, underneath the shelf, when not in use.
so that I can pop a monitor on the front of the bench, & the second was in order to use the bracket under the shelf so that I can stash the monitor out of the way, underneath the shelf, when not in use.
I really like this, to me this looks like an original ancient piece.
How is this going to be rustprotected?
