DAPPH
as dyslexik as I'm daft
- Messages
- 7,489
- Location
- Near to Cross Hands Llanelli SouthWales GB
Only after the event ???
- Thread starter God mode restorations
- Start date
Only after the event ???
Maker
Most folk just call me; Orange Joe
- Messages
- 10,633
- Location
- Keeler crater
Are you using the kiln to slump plate glass?
Seadog
Save the planet. It's the only one with rum!
- Messages
- 12,947
- Location
- NE London - UK
What's the mould made from. Polished aluminium, perhaps?
Seadog
Save the planet. It's the only one with rum!
- Messages
- 12,947
- Location
- NE London - UK
A coating of what?
Bullet2012
Member
- Messages
- 5,365
- Location
- on average about 200 miles from the ISS.
vegan lard.
roblane65
Member
- Messages
- 2,242
- Location
- Newcastle UK
Well by dinner time I had working paddle shiftsThis afternoon I tried to make the range rover have paddle shifts
View attachment 443708
but sadly it wasn't to be, I've something wrong some where either the power to the transmitter
View attachment 443703
View attachment 443702
it's a fiddly little un pin job , pin in a piggy back cable and then join the original live . then the receiver feed which is
View attachment 443704
scotch locked to a switched live under the center console , everything other than those two is pretty much plug and play .
the .I was only on a couple of hours but it started peeing down , I'm hoping the scotch lock just hasn't pierced the small red live feed for the receiver . that'll be a job for tomorrow now ,at least I havn't got to take everything back out again to check it
View attachment 443706
As we men do I skimmed the destuctions and then skimmed the YT vid as I new better 
checked power to the receiver all good but in my undeniable infinite wisdom I'd connected the power for the transmitter to the wrong white plug a rewire to the correct white plug the feed from the slip ring and jobs a gud un . How can one be pleased and annoyed with yourself at the same time 
arther dailey
Member
- Messages
- 6,907
- Location
- England
brilliant that , admire that sort of skill/knowledge ,chuffed for you.Well by dinner time I had working paddle shifts
Memmeddu
Member
- Messages
- 5,541
- Location
- Italia Sardegna
Practically completely disassembled the Husqvarna K770 Power cutter.
Yet to disassemble the crankshaft and engine block,but this isn't probably required cause it's just 3 years old, and the bearings seem fine , crank seals concern me little bit but the looks fine .
Cylinder is salvageable so I'll keep it ,piston is completely scrap.
I'm pretty confident that they ran this K770 on straight gasoline do to the fact the piston has melted on the top.
But could have been lean too but I didn't found any possible air leaks .
I'm not sure about the cause of the failure but the piston was bone dry no oil and even the pin was dry .
Bottom end is oily cause I've tried to start it using spray oil and brake cleaner ( it does work but had no success with this saw)
Anyways here's the thumbnail for the video which is actually uploading
- Messages
- 13,552
- Location
- England
Or what would you like it to achieve ...
Windy Miller
Semi-Professional Potterer!
- Messages
- 3,674
- Location
- North Kent, UK
Onoff
In the land of the unfinished project I am King!
- Messages
- 12,972
- Location
- Sevenoaks, UK
Love the "safety" goggles!
They're actually sunglasses with a camera built into them I put on for recording the gauges but forgot to turn them on... Just like I forgot to use earplugs
DAPPH
as dyslexik as I'm daft
- Messages
- 7,489
- Location
- Near to Cross Hands Llanelli SouthWales GB
Sounds like a prototype Bki cooker . What type of fire extinguishers and stand by help do you have on hand? 