- Thread starter monkeymark
- Start date
theweldingchippy2.0
Member
- Messages
- 65
- Location
- Over here.
These 2 little babys courtesy of penns performance saws. Looking forward to playing with them
Blobber
Forum Supporter
- Messages
- 3,208
- Location
- lincolnshire
A visit to @My Old Landy and came back with this! 
Nice to see you again Brian
Oh there might be some stuff In it
Nice to see you again Brian
Oh there might be some stuff In it
JEZGUZ
Member
- Messages
- 1,075
A sore mouth, went to a dentist today for an emergency appointment. I've had a broken tooth for a while but the pain was getting bad so almost no sleep last night. Into the chair and got x-rayed, dentist declared that there wasn't enough tooth to save so it would have to come out. Ok says I and by the way I am almost phobic about the injections, no problem she says we'll use this numbing gel first and you'll hardly feel a thing. She lied, I could feel every prod of the needle as it bounced off my teeth and gums. Then after a short wait she reckoned I wouldn't feel anything while she had a poke around, eventually after 2 more syringes full of anesthetic she goes to work on the tooth. I am resistant to local anesthetic it would seem, it hurt a lot and she had to stop, so I've been given a weeks worth of Amoxicillin as she thinks there is an abscess under the tooth and another appointment to be tortured again.
If you have an infection it's common enough for the local anaesthetic to be ineffective, certainly in my case it doesn't work.
The dentist really should not operate on the tooth until the infection is either reduced or gone.
My Old Landy
Engineering Mayhem
- Messages
- 3,581
- Location
- North Lincs
I really should have cleaned it mate, sorry! It was great to see you again, thanks for removing myA visit to @My Old Landy and came back with this!
Nice to see you again Brian
Oh there might be some stuff In it
View attachment 488925
Brad93
Member
- Messages
- 19,085
- Location
- Essex, United Kingdom
that's incredible workmanship
Woody.v8
Blue gluer
- Messages
- 4,207
- Location
- staffs
It really is, I'm hard to please and I am happy with it.
Expensive but I can see why.
Memmeddu
Member
- Messages
- 5,369
- Location
- Italia Sardegna
No baffles?
Memmeddu
Member
- Messages
- 5,369
- Location
- Italia Sardegna
Metabo 6061 s-maticb 5 euro spares and repair
Dormer M4-5-6-10 HSSE spiral tip taps
Dormer M8 spiral tip tap
Didn't need them but they end up in my collection.
Brand new Sicutools ratcheting tap wrench, actually needed this one.
Total of 48 euro shipped
Dormer M4-5-6-10 HSSE spiral tip taps
Dormer M8 spiral tip tap
Didn't need them but they end up in my collection.
Brand new Sicutools ratcheting tap wrench, actually needed this one.
Total of 48 euro shipped
Turbo charged around here.That was quick,
northwest
Searching for the Holy Grail.........
- Messages
- 6,386
- Location
- Manchester UK
"New" lave :-)
Its a Colchester Master and came with most of it's bits. It was at the right money too so had to be done, a couple days with it next week should see it up and running. I think I'll start by giving it a good clean.
Its a Colchester Master and came with most of it's bits. It was at the right money too so had to be done, a couple days with it next week should see it up and running. I think I'll start by giving it a good clean.
JOEPRO
Member
- Messages
- 4,762
- Location
- UK
That's what I normally say with a new old car purchase. Then it ends up on axle stands for a 12 year nut and bolt restoration
