Stuff you have made today

[My Old Landy]

Just for completeness I did a video too I am really pleased I have been able to build this
Thanks again for all the support I have had from the forum and its kind members over the last 7 months

 

[6ply]

Needed to make some replacement vice jaws.

Found some scrap metal plate 600 x 600 x 10 for which I paid £5.00

Seems to machine up quite nice.

 

[Gragson]

Just for completeness I did a video too I am really pleased I have been able to build this
Thanks again for all the support I have had from the forum and its kind members over the last 7 months

Nice work that MOL

Thought the iron with the light looked pretty flash, then saw it was a Parkside, are they any good?

 

[My Old Landy]

Nice work that MOL

Thought the iron with the light looked pretty flash, then saw it was a Parkside, are they any good?

Cheers my friend
They are good but you may have noticed a change as it ran out of charge I think for small jobs it works well. Anything major then use a mains one

 

[Dcal]

Today I made a clamp so I could change the position of our mains water toby.

Worked a treat.
The existing stopcock box was in the middle of a hedge so I wanted to move it.
Also put in a box for the new fibre connection, which is why the hole is so big.

 

[striker]

I finished this...

For use with this

Now I need to make some press plates out of these...

They're 30mm thick and because they such a large diameter won't fit in my little bandsaw. I have a 9" grinder. Would it be feasible to use that with some cutting discs? If so what type? Will it take forever? Any advice Gratefully received.
Paul.

 

[Screwdriver]

Yes a 9" grinder will chop that up easily. Remember to cut 1mm deep slots and just "saw" your way through the entire length of the cut. Don't cut all the way through in one go, it will eat your disks up in no time.

 

[striker]

Yes a 9" grinder will chop that up easily. Remember to cut 1mm deep slots and just "saw" your way through the entire length of the cut. Don't cut all the way through in one go, it will eat your disks up in no time.

How many discs should I buy? I need to cut two 8"x4" pieces from one of the discs...I mainly use my 9" grinder for building work...just use my little grinder for metal working. So I don't want to buy more than I need as I can't see them getting used. I believe they have a shelf life.

 

[Screwdriver]

Well you should be able to get through 30mm with a 5 inch/125mm or even a 115mm angle grinder. My seat of the pants estimate would be 3-4 disks per 8" cut, 2-3 disks for the 4". They don't "go off" in my experience, you should always assume it's going to jam/explode in your face so it really shouldn't matter if/when they do. I have tons of very secondhand, slightly rusty cut off disks which were low cost versions when they were made (back in the late '80's). Rarely have any problems with their age but if you have some "out of date" disks you're not happy with, I'll happily dispose of them for you!

I assume metal cutting disks for the 9" grinder would be a LOT more expensive and a bit thicker. Plus a fair bit more grief if it all goes a bit Pete Tong. Don't know how many you'd use but each one will have a fair bit more material before you "bottom out". So

All depends how careful you are letting the tool do the work, not getting the disk to hot, light pressure on a nice straight cut etc. I really wouldn't like to guess how many 9" disks you'd need, too many variables. Maybe someone else here has more experience with them. I only break out the 9 incher when I'm feeling brave/reckless.

 

[striker]

I think once I've made the long cuts, I will be able to cut to length, across the 4" on the bandsaw.

 

[nickk]

A window frame and pintels and retaining hook.

 

[Blue Chips]

It seems that sometimes smaller jobs take longer. There was a short (40-inch) missing section of chair rail in one of the parlors of the old farmhouse we're restoring. The chair rail consists of four separate pieces of moulding. I had a couple of router bits that I used to make two of the pieces, but one of the pieces had a profile that didn't match any of my shaper knives, router bits, or antique moulding planes. So I stopped at a local industrial supply house that has an enormous selection of router bits (an entire aisle), but none of them matched the exact pattern and size, so to make that one piece of moulding, I ended up using a combination of two different router bits, a small shoulder plane, a sanding block, and my radial arm saw (to cut a groove to receive a 1/8" diameter wooden dowel). I probably spent more than four hours to make one 40-inch piece of moulding. It does, however, match the original pattern quite nicely. I haven't installed that fourth piece yet, but I'll post a photo after it's installed and I've touched up the plaster and primer.

Here's a photo with three of the four replacement pieces installed:

Here's the fourth piece, which I made today. You can see the wood dowel glued into the groove.

Just a quick update to my quoted post above. I installed the replacement pieces of chair rail moulding that I made, touched up the plaster, and slapped on the first coat of primer. It seems to match up to the original fairly well. It still needs a bit more sanding and another coat of primer to totally hide the joint between the old and new sections, but so far I'm satisfied with the result.

 

[Tupers]

I made a big hole in a Transit and then I made some bits to fill the hole!

 

[Erie Fred]

I finished this...View attachment 383080
For use with this

View attachment 383081

Is that press brake attachment purchased ? I have someone looking for one like that with interchangeable top punches

 

[striker]

Yes it was... A guy in Sheffield makes them. There's demo's on YouTube, Cyclops press brake.

 

[Scalarocco]

Is that press brake attachment purchased ? I have someone looking for one like that with interchangeable top punches

Try Swag off road. They sell press brake kits in the US.
https://www.swagoffroad.com/collections/swag-press-brake-kits

 

[nickk]

Another arch braced gate,shame about the climbing plant!

 

[Fraserb]

Making a start for spring cropping.

 

[Geoffm]

My coolant pump on my Colchester Chipmaster died a few years ago. It was an old fan motor with "drill powered" pump on the shaft. The swarf did not do the impeller any good, and I haven't used it for years. Around 18 months ago, I bought one of these (although the price has gone up)

15.48￡ |CNC machine tool cycle oil pump lathe cooling pump three phase electric cooling pump 380v three phase single phase electric pump|Pumps| - AliExpress

Smarter Shopping, Better Living! Aliexpress.com

www.aliexpress.com

A wet day and I finally got around to fitting it. I removed the plate over the sump, cut a hole in it, bolted on the new pump and found a hose and squirty nozzle thing in the back of the shed, adn made a bracket. Not a thing of beauty but it works.
The sump was disgusting after sitting there - entire species of swamp creaters have evolved in it.

 

[Turbo]

Making a start for spring cropping.

View attachment 383297View attachment 383298

That looks like a 8 furrow reversible, what's pulling it?

What's the advantage of the slatted mouldboards? No discs either?