eLuSiVeMiTe
Member
- Messages
- 16,438
- Location
- ......
Forester is a boat unladen. Don't envy the drive. Had a xt for a few years went like stink
- Thread starter Dieselman 63
- Start date
Dieselman 63
Forklift Certified
- Messages
- 5,868
- Location
- Wellington, New Zealand
They are, you’re right! I love them though, been driving them for years. This is the fifth one at home, my first though, with the ej20. Have an ej25 sg5 chassis at home too, same shape, seems to drink more gas for marginal performance increase.
Apparently I beat another guy to buying this who wanted it TO TURN IT INTO A PIECE OF MODERN ART. Jesus wept. This baby had a close call with the gas axe! I’m an artist myself and it pains me to see lovely working machines turned into garden art.
When the Forester was launched over here the local dealers had a day at Todds Leap off road driving centre. The off road instructors were amazed when this 'car' went around their full off road course normally reserved for proper 4x4's!
Dieselman 63
Forklift Certified
- Messages
- 5,868
- Location
- Wellington, New Zealand
slim_boy_fat
Member
- Messages
- 29,363
- Location
- Scottish Highlands
Well done on rescuing it and 'safely' 
getting it home! 
getting it home!
Dieselman 63
Forklift Certified
- Messages
- 5,868
- Location
- Wellington, New Zealand
Whilst cleaning I managed to find some rich iron deposits. Unfortunately they were on the machine! The mounting lugs were full of caked rust and grease. The T slots were full of grease and swarf. All of it came out in the end though.
I love wet days as they’re ideal for waterblasting. Outside my house a small river forms in heavy rain, and I spotted these happy ducks playing in it!
I love wet days as they’re ideal for waterblasting. Outside my house a small river forms in heavy rain, and I spotted these happy ducks playing in it!
Dieselman 63
Forklift Certified
- Messages
- 5,868
- Location
- Wellington, New Zealand
Getting the table bracket off the column was tough. It’s been repainted once and had been done in situ, probably never been apart before. Lots of oil, twisting with a wooden handle through the eye, and finally a vertical raise with some wooden-plank-protected love taps from a 6lb hammer and it was free.
The column looks in great shape, and that should polish up nicely. I want the bracket repainted and back on the column before I mate the column to the drill base again. It will save time in the future.
The switch I have looks a good fit on the machine, nice and early c20. I’m still undecided on the colour for it, Denbigh drills were originally a blue/grey but I might go crazy yet
The column looks in great shape, and that should polish up nicely. I want the bracket repainted and back on the column before I mate the column to the drill base again. It will save time in the future.
The switch I have looks a good fit on the machine, nice and early c20. I’m still undecided on the colour for it, Denbigh drills were originally a blue/grey but I might go crazy yet
Dieselman 63
Forklift Certified
- Messages
- 5,868
- Location
- Wellington, New Zealand
God mode restorations
Member
- Messages
- 8,150
- Location
- uk colchester
That's fine lol. You only need to worry when the rear tyres are scraping the tops of the wheel wells and you got to stick lumps of stuff between the rear springs
gaz1
Member
- Messages
- 20,534
- Location
- westyorkshire
on looking elsewhere i found drill speeds for the above drill or close relatives to it
https://archive.org/details/advancedmachini00unkngoog/page/n204
page 198 onwards about halfway up the bar at bottom of screen
https://archive.org/details/advancedmachini00unkngoog/page/n204
page 198 onwards about halfway up the bar at bottom of screen
Dieselman 63
Forklift Certified
- Messages
- 5,868
- Location
- Wellington, New Zealand
So I decided to have a look in the power feed box. Wow. This is a complete mess. It’s meant to be oiled so no grease at all, there’s rust here too, so the grease didn’t even preserve much. They really slathered it in. On the plus side, the splines of the dog clutches function well. No restoration is complete without a ball bearing firing across the room, in this case I caught the ball but the spring is m.i.a.
Dieselman 63
Forklift Certified
- Messages
- 5,868
- Location
- Wellington, New Zealand
Similar but not my drill. Mine has an acme raising mechanism whereas that one has a screwed on rack.
This is mine
slim_boy_fat
Member
- Messages
- 29,363
- Location
- Scottish Highlands
God mode restorations
Member
- Messages
- 8,150
- Location
- uk colchester
They are awesome drilling machines. Hopefully be sorting my one out soon.
Dieselman 63
Forklift Certified
- Messages
- 5,868
- Location
- Wellington, New Zealand
Do you have a Denbigh too?
Dieselman 63
Forklift Certified
- Messages
- 5,868
- Location
- Wellington, New Zealand
This is going to be good, I'm looking forward to the progress reports.
The first job is stripping the paint on both the table bracket and table rise casting. Once these are primed and repainted, I can mate the column back to the base. This will consolidate the restoration process and stop the garage being filled with iron!
But in reality, we no longer have [afaik] any working coal fired power stations in the UK, thanks mostly to Tree huggers, Greens and the generally ecologically hoi polloi, convinced by the above through the interweb and ecen Twitter and/or Faceslap, and for all I know other assorted media sources, newspapers, magazines of certain political leanings, not to mention so called 'social media' loke Twitter,Faceslap and something called 'Snapshat, Skype etc.
it'd a bit off topic.... but our coal power stations are pretty much all still up and running - they're just running at minimum power output, but still there/running and ready to wind up to full power just incase we need them - they're production just short of 6% of our demand right now
https://www.gridwatch.templar.co.uk/
coal is one of the most expensive forms of generation, so it's at the back of the queue when we need power
God mode restorations
Member
- Messages
- 8,150
- Location
- uk colchester
It's very similar. Mine is a bradson I believe.
slim_boy_fat
Member
- Messages
- 29,363
- Location
- Scottish Highlands
As a matter of interest only, how long would it take them to reach full grid contribution?
