Today I acquired...........

[dobbslc]

I'm knocking a couple of new doorways through as soon as I finish the berludddy stairs

 

[RichardM]

A pressie from me to my little TS mill



Well wrapped. What's in the box?



One of these,



and two of these.



What's in the tube?



Aikron DRO display with rpm, 1 metre thin profile magnetic scale and two reader heads from BMR Measurement Solutions.

More to follow when I fit it.

 

[The_Yellow_Ardvark]

A dead thing.
An ex lighter.
It has ceased to be.

A Miniature 16mm camera.

WD Insulation tester.

 

[arther dailey]

Today I acquired a snap on clutter trap foc,mate had it as a welding cart hence the upside down top tray.

View attachment 412697
View attachment 412698

FOC ! what ever you stepped in bag some up for me, I will pay carriage..

 

[GRW]

Today I aquired this set. Mostly I'm metric, but these popped up on FBMP & you never know when they'll come in handy. Almost complete set (2 small taps missing) UNC/UNF/NPT Tap & Die set.

 

[sparkysy]

@The_Yellow_Ardvark
My dad has one of those insulation resistance testers. They give out a good belt if your holding onto the probes.
Myself and my brother used to play see how long you can hold onto it when we were younger!

 

[MattF]

Arrived yesterday.

 

[angellonewolf]

Arrived yesterday.

View attachment 413064

you already got a shiney one why need another

 

[MattF]

you already got a shiney one why need another

I'm working on the: "He who dies with the most tools wins" philosophy. Besides, who needs excuse to buy another tool?

 

[Seadog]

Some decent firebricks.

 

[slim_boy_fat]

Myself and my brother used to play see how long you can hold onto it when we were younger!

That'd be back in the days when kids were allowed to find things out the hard way? Within reason of course .

 

[sparkysy]

Very much so, the wind up insulation testers didn't half give you a belt! Dad still has a few testers from his working days, we used to test ourselves with them all, winner (who was deemed to have held on longest) use to get to choose the fizzy pop for the week! Really nice testers, not like the ones we have now but perfect for what they need to do and some amusing antics too!

 

[Cuthy246]

Acquired a little while ago courtesy of @My Old Landy (Thanks again) but got to use it for first time today and it was beyond useful. Have managed to determine our centrifuge is going to the big lab in the sky. It is giving a no speed sensor error. Using the scope I have been able to check the sensor(fine), analogue signal (fine), digital signal (fine). Basically signal is absolutely fine all the way to main processor. Have also checked clock signal and supply voltages all fine too. Problem must be internal to the chip . No parts available as this was built in the early 90's and is long discontinued. Time to drop a few ££££ on a new one.

 

[Sergei Slovenija]

Acquired a little while ago courtesy of @My Old Landy (Thanks again) but got to use it for first time today and it was beyond useful. Have managed to determine our centrifuge is going to the big lab in the sky. It is giving a no speed sensor error. Using the scope I have been able to check the sensor(fine), analogue signal (fine), digital signal (fine). Basically signal is absolutely fine all the way to main processor. Have also checked clock signal and supply voltages all fine too. Problem must be internal to the chip . No parts available as this was built in the early 90's and is long discontinued. Time to drop a few ££££ on a new one.

View attachment 413143View attachment 413144

Replace all electronics with a frequency controller?

 

[Cuthy246]

Replace all electronics with a frequency controller?

While that would get it spinning the problem is it has to maintain a set rpm within a very tight tolerance. Specs from manual are 100 to 14000 rpm with a tolerance of +-5 rpm across the range. The board also controls the refrigeration unit at the back of the machine, soft start, electronic braking, run timer, and safety interlocks. You can also program it to run x speed for x mins then y speed for y mins then z speed for z mins all automatically controlled. Getting a new board and everything set up to run it to the standard that we need would take ages and since we use it every day it makes more sense for us to get a new one which will be here by the end of the week.

 

[OJCar]

Thanks @Onoff
Very well packed!
(Who packed it for you ? )

 

[My Old Landy]

Acquired a little while ago courtesy of @My Old Landy (Thanks again) but got to use it for first time today and it was beyond useful. Have managed to determine our centrifuge is going to the big lab in the sky. It is giving a no speed sensor error. Using the scope I have been able to check the sensor(fine), analogue signal (fine), digital signal (fine). Basically signal is absolutely fine all the way to main processor. Have also checked clock signal and supply voltages all fine too. Problem must be internal to the chip . No parts available as this was built in the early 90's and is long discontinued. Time to drop a few ££££ on a new one.

View attachment 413143View attachment 413144

You are most welcome, I am glad it has proven useful

 

[Onoff]

Very well packed!
(Who packed it for you ? )

You're welcome.

Bloody cheek, packing is the one skill I do have! My Christmas pressie wrapping is an art form

 

[angellonewolf]

You're welcome.

Bloody cheek, packing is the one skill I do have! My Christmas pressie wrapping is an art form

mines not it looks like a toddler done it

 

[Keith 66]

Today I acquired a Slip roll from my scrappy mate, I borrowed it about ten years ago for a job and cleaned it up then, he didnt want to sell it so its been sitting in his yard ever since, he finally decided to run it in and i happened to pop in just as it had been chucked on the wagon.
So another clean up!