Today I acquired...........

[The_Yellow_Ardvark]

Perhaps a Moderator can change your avatar name to " I Want ! "

Much I need. Many item I would want. Many I like.
Some I do not like, or want or need.

Just something brings back a good memory

 

[Arc Tourist]

Much I need. Many item I would want. Many I like.
Some I do not like, or want or need.

Just something brings back a good memory

Yeah, I also find that some of the old things I remember while growing up bring back good memories.

 

[Olderisbetter]

We need a
I want button.

My gran had something similar. That and an electric blanket was plugged into a 15amp wall socket.

Then like an old auto eject kettle lead they would be fired out.

As soon as i spotted it i knew it would make a nice looking item for my pre 50's room which is going to get filled with nostalgic items

 

[jonclancy]

… enough filler rod in the right place to finish my final test piece on my C&G Level 2 TIG Aluminium course.

I am rather chuffed!

 

[MattF]

Well done.

 

[25.4_mechanic]

I acquired a look at and test run with an Arboga U2508 milling machine today.

All eight speeds run perfectly (100-2,900rpm - what a range without having to touch a belt).

When measuring the runout at the end of the quill, I first thought I wasn't measuring at all until I swapped the 0.01 for a 0.001 clock, then the pointer shook a little.

Now I'm having a hard time thinking ....

Are Arboga machines (Sweden) widespread or even known among you?

Have a nice evening

Carsten

--

 

[Maker]

Are Arboga machines (Sweden) widespread or even known among you?

I've never seen a mill but Arboga drills pop up from time to time, usually command a bit of a premium but they look very well built.

 

[Hood]

I acquired a look at and test run with an Arboga U2508 milling machine today.

View attachment 328957

All eight speeds run perfectly (100-2,900rpm - what a range without having to touch a belt).

When measuring the runout at the end of the quill, I first thought I wasn't measuring at all until I swapped the 0.01 for a 0.001 clock, then the pointer shook a little.

Now I'm having a hard time thinking ....

Are Arboga machines (Sweden) widespread or even known among you?

Have a nice evening

Carsten

--

It is really more a Mill/Drill, only for relatively light milling.

I have an Arboga pillar drill, they don't look much but are beautiful machines, I was after one for years and then one came up on eBay and I got it. It arrived in bits, I had paid for it to be put on two pallets lying down, it arrived lying down right enough but that was because it was originally standing on one pallet and the plastic binding had snapped. I emailed the seller (a machine dealer) , sent pics etc and he refunded in full and told me to scrap it, I managed to repair it so I was happy

 

[Rannsachair]

I acquired a look at and test run with an Arboga U2508 milling machine today.

View attachment 328957

All eight speeds run perfectly (100-2,900rpm - what a range without having to touch a belt).

When measuring the runout at the end of the quill, I first thought I wasn't measuring at all until I swapped the 0.01 for a 0.001 clock, then the pointer shook a little.

Now I'm having a hard time thinking ....

Are Arboga machines (Sweden) widespread or even known among you?

Have a nice evening

Carsten

--

As said better known own for their drills, quality kit. http://www.lathes.co.uk/arboga/

 

[25.4_mechanic]

It is really more a Mill/Drill, only for relatively light milling.

I have an Arboga pillar drill, they don't look much but are beautiful machines, I was after one for years and then one came up on eBay and I got it. It arrived in bits, I had paid for it to be put on two pallets lying down, it arrived lying down right enough but that was because it was originally standing on one pallet and the plastic binding had snapped. I emailed the seller (a machine dealer) , sent pics etc and he refunded in full and told me to scrap it, I managed to repair it so I was happy

You made a good bargain in the end ... At least you had enough capital to put into the repair.
(However, I am annoyed by things that have been destroyed due to sloppy cargo securing/packaging, and even more so when people have been harmed in the end.)

How's your machine called? Surly you've shown it here ... got a link?

As said better known own for their drills, quality kit. http://www.lathes.co.uk/arboga/

Thanks for that reply, "quality kit" feels good - The link: I am amazed again and again at what you can find on his site - and Tony is also very accessible, which is a bit surprising considering what he has all to deal with.

Carsten

--

 

[Hood]

At least you had enough capital to put into the repair.

It cost me only time to fix

How's your machine called? Surly you've shown it here ... got a link?

What do you consider the best smallish pedestal/bench drill?

For me it is an Arboga, they are Swedish and I have always considered them a cut above the rest in their class and I have used quite a few different makes that people consider the best. Quite a few variants , one with a XY table seems to be quite common, mine is just the more basic type although...

www.mig-welding.co.uk

 

[DAPPH]

Narrow end in direction of travel or if unsure tabs trailing, so B.

Yep B .... looking from the direction of travel the inner tail trails .. Here is picture or three of " "Fenners ( marked up belting " off my lathe ( lathe needing a new 240 volt 1/2 h 3300 rpm motor with a 3/4 spindle not a 19 mm spindle as the two year old replacement for the 76 yr old original one one died a sudden fuse blowing death ( bloody Chinese rubbish )

You will need to make one or two adjustments after fitting a new belt , for it beds in . I think Fenner's recommended 1/2" ( 13 mm ) of full top to bottom play using a straight edge on the top edge of the belt .. but that's one hell of a tight belt if the bearings are a bit worn .
Keep the unused links safe in a heat sealed up heavy poly bag for future events .
There is a YouTube video by Fenner's about fitting their link belts

 

[DAPPH]

Just had a thought ...

Get a Sharpie permanent marker and once the belting is fitted correctly mark the direction of run on every fifth link or so just incase you need to remove it in a couple of years as it's so easy to put it back on the wrong way round

 

[25.4_mechanic]

It cost me only time to fix

Well done

What do you consider the best smallish pedestal/bench drill?

For me it is an Arboga, they are Swedish and I have always considered them a cut above the rest in their class and I have used quite a few different makes that people consider the best. Quite a few variants , one with a XY table seems to be quite common, mine is just the more basic type although...

www.mig-welding.co.uk

Your machine looks a bit like an EM825, but also a bit different - rumors are there was a very solid transitional version on the way to the U2508, at least with the gear levers on the right.

Otherwise, the gearbox seems to be the same as in the U2508!

Today, when shifting gears at a standstill, I noticed that the upper lever engaged in the gear a little more unwillingly.
It was easier to engage just before coming to a standstill or while turning the spindle by hand.

Could the oil level in the gearbox head play a role?

How is it with your machine?

Carsten

--

 

[Hood]

Occasionally the teeth don't mesh when changing gear so you have to rotate the spindle slightly.

 

[25.4_mechanic]

Just had a thought ...

Get a Sharpie permanent marker and once the belting is fitted correctly mark the direction of run on every fifth link or so just incase you need to remove it in a couple of years as it's so easy to put it back on the wrong way round

At first I thought: Naa, I've got it now ... but you're right, I'm not getting any younger and it could be someone else I'm helping ...

Thanks!

Carsten

--

 

[MikeBB1970]

Crossing the equator? My dad did that on a aircraft carrier. The photos were interesting

My dad was on this lovely ship as a Navy sparky up to about 1958.
I was born early sixties and he was out of the service by then.

The name MikeBB just refers to my first gun
It fired plastic "bbs" . It was a cheap all plastic pistol.

Here's a similar one, but metal, that I acquired lately.
It was disposed of at our local recycling centre.

 

[MikeBB1970]

Not much acquirement going on for me, I got a cheap visor for when using the grinder and lathe.

A couple of bicycle puncture repair kits. A hand held 'scope on order.

Wool ! I cant even knit . Wife's charity knitting malarkey, teeny socks and jackets for the premature baby ward.

Quite a few of different colours of those wool packets

 

[Hood]

It was actually yesterday I got it, yet another toy for my African lady

Shows up in the phones app.

 

[25.4_mechanic]

yet another toy for my African lady

Congrats!

Do the caps push down on the Schrader valves to get to the pressure?
Is the energy for the caps to be able to transmit data generated by movement, centrifugal forces or else?

Thanks!

Carsten

--