Stuff you have made today

[Kram]

Pigeon poo shelf horizontals

It was still damp, and started to rain a bit but continued anyway. Rubbish but adequate for a shelf unit. Got a few lung fulls of zinc fume. They will get the minimum grinding tomorrow and some thick paint
Ordered some 0.6mm wire for next time. Couldnt get a suitable wire speed with 0.8

 

[DAPPH]

Today I (almost) finished making a bird box. I made it more for practising techniques (mostly power tool ones this time) than because we particularly needed a bird box, hence the over-done joinery and the possibly unnecessary roof covering.

Made from oak (joined from narrow bits into wider bits) with the roof coated in some lead flashing that came off my roof a few years ago and which I battered flat and then hit repeatedly with a ball peen hammer to give it a dappled appearance. The roof (in three pieces) is currently only held on with gravity as I haven't decided how I'll attach it yet. For scale, the hole is sparrow sized (32 mm) and the fingers of the joints are 9 mm.

View attachment 248333

View attachment 248334

The lead still needs trimming at the back and fixing in some way yet to be determined.

The roof has a couple of blocks of wood spaced to match the internal dimensions of the bird box and is held on with a single stainless screw from behind so it can be taken off for cleaning if/when required:

View attachment 248335

Put a posh stainless steel pin in the internal front block through the apex wall so you can pull it out for cleaning the box out in November . I've done several bird boxes like that. I'd also put a alu or stainless 32 mm holed washer with at least a 55 mm OD dia to prevent squirrels chewing their way in to get at the eggs of chicks .
I've had to make my own new nesting boxes an inch & a half deeper from the entrance hole to the bottom of the box because I saw a squirrel with its arm deep inside a nest box fishing for baby blue tits. To assist the fledglings in getting out the deeper boxes I've used a Dremel to put a ten or more 8 mm spaced horizontal cuts on the intern front face for them to scramble up when they're ready to leave the nest .

 

[selectedgrub]

Hi @Jay1st it was a speaker system.
https://selectedgrub.blogspot.com/2019/02/blog-post_26.html

The lady who owned moved to a rest home and had no room for it
I offered to hang it from the ceiling.

I am re purposing into junk art to give back.
https://www.mig-welding.co.uk/forum/threads/junk-art.104630/#post-1650460
I get to keep some of it.
Thanks for the interest.

 

[DAPPH]

A fiver. A woman brought a bread maker round as'The paddle thing doesnt go round' so I tapped it with a hammer handle and now it does.she got a speaker thing out of the cat that had a
stuck battery in it, so I banged it on the bench and the battery dropped out, about a minutes 'Work and she forced a fiver on me.Wish I got that hourly rate a bit more often...

Think & dream bigger ........ My Mrs got £234 US trading dollars two seconds after pressing buy now & sell when the stock reaches 2.085 dollars

 

[nickk]

Finally the canvas got stretched over my canopy featured previously,1 prospective customer came for a viewing,and one of the national museums is keen ,but not on my timespan.the baler twine will be replaced with S/S cables.

 

[Dr.Al]

Put a posh stainless steel pin in the internal front block through the apex wall so you can pull it out for cleaning the box out in November .

It's got a stainless screw from the rear that serves the same purpose (you have to take it off the wall for access, but you'd need to do that anyway to clean it).

I've done several bird boxes like that. I'd also put a alu or stainless 32 mm holed washer with at least a 55 mm OD dia to prevent squirrels chewing their way in to get at the eggs of chicks .

That's a good point. We don't get many (any?) squirrels round here, so I'm not too concerned about it at the moment, but I might add a washer if I ever get round to moving house.

 

[Kram]

Shelf unit is Done! (Opposite lathe, photo from doorway) More than doubling my usable shed storage area. I have soo many items for it, there will be zero spare space by tomorrow.

Except Ive lost two of the side horizontals. I am sure they will turn up, just after the shelf gets fully loaded.

 

[MattF]

I made the mistake of deciding to change a light fitting.





Ten minute job my ar*e.

 

[Dr.Al]

Matt you should know better, no 10 minute job is ever 10 minutes.

One of my co-workers in my last job had a surprisingly accurate method of calculating how long a job would take: "think of how long it should take, double it and go up a unit". So a 5 minute job takes 10 hours, a 1 day job takes 2 weeks.

 

[Maker]

One of my co-workers in my last job had a surprisingly accurate method of calculating how long a job would take: "think of how long it should take, double it and go up a unit". So a 5 minute job takes 10 hours, a 1 day job takes 2 weeks.

Shockingly accurate! I started repairing the shed at the start of July, didn't think it would take much more than a week, I'm putting the felt on today!

 

[slim_boy_fat]

I started repairing rebuilding the shed at the start of July,

Fixed that for you.....

 

[Maker]

Fixed that for you.....

When I started I was only repairing it.

 

[Jay1st]

One of my co-workers in my last job had a surprisingly accurate method of calculating how long a job would take: "think of how long it should take, double it and go up a unit". So a 5 minute job takes 10 hours, a 1 day job takes 2 weeks.

I do like Scotty in Startrek, Factor 2 and round up.
Works every time.

 

[slim_boy_fat]

and round up.

Weeds don't grow in space.... [OK, I know where the door is >> ....]

 

[MattF]

That's so crap it's funny.

 

[Jay1st]

Hi @Jay1st it was a speaker system.
https://selectedgrub.blogspot.com/2019/02/blog-post_26.html

The lady who owned moved to a rest home and had no room for it
I offered to hang it from the ceiling.

I am re purposing into junk art to give back.
https://www.mig-welding.co.uk/forum/threads/junk-art.104630/#post-1650460
I get to keep some of it.
Thanks for the interest.

Anymore details about that fabulous bike ?????

 

[Hitch]

Little replica propeller...
Out of some reclaimed 4x2.
Might bang a clock in the centre, might just leave it.

 

[fizzy]

Little replica propeller...
Out of some reclaimed 4x2.
Might bang a clock in the centre, might just leave it.

That must have taken you ages! Lovely job!

 

[Hitch]

That must have taken you ages! Lovely job!

Nah, couple of hours.
Not sure how well balanced it is mind

 

[Morris]

Following on from my modified manifold I made the adapter for the throttle body. The cast bend welded well but was a bit dirty. Please excuse the welding, it's not great.