- Thread starter God mode restorations
- Start date
slim_boy_fat
Member
- Messages
- 29,363
- Location
- Scottish Highlands
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 20,000
- Location
- Going Away.
We don't get magpies up here, I wonder if it's too cold for them?
Yes, plus easy pickings down here.
Barking Mat
Cuddler of hedgehogs.
- Messages
- 13,534
- Location
- France, Brittany.
Hood
I am obsessed.
- Messages
- 17,884
- Location
- Carnoustie, Scotland
They are on their wayWe don't get magpies up here, I wonder if it's too cold for them?
When I lived in Perth in about 1990 there were loads but in Carnoustie just 40 or so miles away I had never seen one, now they are seen here and are increasing in numbers.
Hood
I am obsessed.
- Messages
- 17,884
- Location
- Carnoustie, Scotland
Ta, sometimes it is good, others not so good
Barking Mat
Cuddler of hedgehogs.
- Messages
- 13,534
- Location
- France, Brittany.
Finally, finished off the plasterboarding in our bedroom, I'd planned to fit wooden c section round the door frames to our his n hers walk in wardrobes, but seeing as every hardware shop is shut and would have cost in the region of 60 quid, I was reticent. So yesterday I whacked some 76mm strips of plasterboard round the internal door frames, and podged, then today sanded, only I forgot to turn the vacuum on, before I realised, I couldn't see from one side of the room to the other. It then took me 40 minutes to Hoover the room before I dare tell Wifie what id I'd done. Oh well, bedding changed, looks good for a complete amateur I think.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 20,000
- Location
- Going Away.
Hood
I am obsessed.
- Messages
- 17,884
- Location
- Carnoustie, Scotland
Nope, that was where the projectile that his wife threw at him landed
Barking Mat
Cuddler of hedgehogs.
- Messages
- 13,534
- Location
- France, Brittany.
Obviously, lifes too short, and I'm not a perfectionist.
But after 4 years, we have a bedroom! And wardrobes!
You'd think that would cheer up t'other half.
Anyway, what was that saw you stuck a handle on, what's that for.
I get that gasket paper in the post tomorrow, I'm going out!
But after 4 years, we have a bedroom! And wardrobes!
You'd think that would cheer up t'other half.
Anyway, what was that saw you stuck a handle on, what's that for.
I get that gasket paper in the post tomorrow, I'm going out!
Barking Mat
Cuddler of hedgehogs.
- Messages
- 13,534
- Location
- France, Brittany.
Oh, that's where I put a plug hole in the wrong place, I thought you were referring to the 'slight' gap around the beam.
Perfectionism is for when I'm older and bored, can't see that happening.
Perfectionism is for when I'm older and bored, can't see that happening.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 20,000
- Location
- Going Away.
The brass Tap item.
Was meant to be away for a few days, so Took some bits with me to clean it up.
But, due to one thing and another I didn't do it when I was away.
Ok. I took a short cut and painted the handle before I left.
So, instead off Brasso and a rag, it was a buffing wheel.
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 20,000
- Location
- Going Away.
Michael Bennett
New Member
- Messages
- 10
- Location
- England Surrey
What was it in a previous life
DVLA wheel clamp.
northwest
Searching for the Holy Grail.........
- Messages
- 6,597
- Location
- Manchester UK
Been in the Bat Cave all day and making barrels again. Well, not strictly true, I have the barrel blanks and I am profiling and chambering them for quite a longish list of gun builds.
This is one I do as a special order, very lightweight carbon fibre pre-stressed AR-15 barrel in .22 rimfire for one of the practical shooting lads:
Thought I would show you how I set up for chambering. I use a "range rod" to get the centre line of the barrel true to the centre of the spindle. This is a rod with an accurately ground bush on one end, I have a selection of them for different calibres, the rod is held firmly in the tailstock and I take two measurements jiggling the barrel at both ends of the spindle:
I use two clocks, both tenths and I will accept half a thou but no more:
Usually takes me a good half hour before I am happy and ready to start to cut the chamber, sometimes longer and if I can't get it right I just stop, do something else and then come back to it later.
This is one I do as a special order, very lightweight carbon fibre pre-stressed AR-15 barrel in .22 rimfire for one of the practical shooting lads:
Thought I would show you how I set up for chambering. I use a "range rod" to get the centre line of the barrel true to the centre of the spindle. This is a rod with an accurately ground bush on one end, I have a selection of them for different calibres, the rod is held firmly in the tailstock and I take two measurements jiggling the barrel at both ends of the spindle:
I use two clocks, both tenths and I will accept half a thou but no more:
Usually takes me a good half hour before I am happy and ready to start to cut the chamber, sometimes longer and if I can't get it right I just stop, do something else and then come back to it later.
Barking Mat
Cuddler of hedgehogs.
- Messages
- 13,534
- Location
- France, Brittany.
Carbon fibre barrels, didn't know they existed, how do they compare with use? I mean do they wear internally?
