Snap on 130 feed wire tensioner!

[RWD3M]

Hi @Onoff

Just been scouring this section as I have a part of my Cebora failed but unusually, it isn't the tensioner arm, it's the housing with 3 screws in it that clamps the torch in place that has fallen apart.

Just wondered if you'd had a need to model this part?

I'm in the process of drawing it up as we speak but I'm not the world's quickest!

 

[Onoff]

Just wondered if you'd had a need to model this part?

No

 

[RWD3M]

No

Bu99er!

Well, I've done it now so will try printing one off and see what I get. This may take a while!

 

[welditshut]

My lad just downloaded the one from the Pinshape link above. PM me your address and we'll print one for you to try.

It'll be done in grey PETG.

Printing now.

Hello are you still 3D printing the Snap On 130 wire feed tensioner.

 

[Onoff]

Hello are you still 3D printing the Snap On 130 wire feed tensioner.

As quick as finding it and hitting print.

 

[welditshut]

As quick as finding it and hitting print.

Hi any chance you could print me a couple one for spare. How much do you want if you can.

 

[hondacode]

As quick as finding it and hitting print.

For the life of me, and I thought I knew how to use forums, I can't find how to send you a direct message.
Long time lurker, first time account.

Have just busted my tensioner like all thsoe in here before me, been scouring the interwebs, then was about to boot up Fusion360 and saw you'd already been down this path.
Could you please let me know how much you want for one?

I only print in PLA currently and the damn thing needs setting up again - add to the list

 

[badabec]

Tap on 'onoff'. Then send direct message will appear.

 

[Wozzaaah]

For the life of me, and I thought I knew how to use forums, I can't find how to send you a direct message.
Long time lurker, first time account.

Have just busted my tensioner like all thsoe in here before me, been scouring the interwebs, then was about to boot up Fusion360 and saw you'd already been down this path.
Could you please let me know how much you want for one?

I only print in PLA currently and the damn thing needs setting up again - add to the list

New members cannot send private messages, it's an anti-spam measure.

 

[hondacode]

Yeah, that's logical, I can understand having run forums.

 

[Onoff]

Hi any chance you could print me a couple one for spare. How much do you want if you can.

Two in print now.

Plenty of cheap "ready to go" enclosed printers now. No setting up required.

Not quite Bambu X1C but seemingly quite good. Elgoo Centauri Carbon, Creality K1C etc.

 

[Onoff]

Two done in grey PETG with bronze PLA support layers.

 

[CharBennett]

You never done mine, I waited ages but no response.

 

[Onoff]

You never done mine, I waited ages but no response.

Apologies if I missed your request. I see I had a pm from you in April I see saying if I still needed measurements you could assist. I was super busy then with the new job.

Are you sorted for one?

 

[Onoff]

@CharBennett just looked back on this thread. I presumed from this exchange below that you were getting it sorted with @Bullet2012 :

 

[Onoff]

Hi any chance you could print me a couple one for spare. How much do you want if you can.

Are you still after a couple of these?

 

[RWD3M]

You never done mine, I waited ages but no response.

Now that's just plain rude! There are much better ways of approaching this, a PM for example.

 

[CharBennett]

Now that's just plain rude! There are much better ways of approaching this, a PM for example.

I would never be rude on purpose.

 

[RWD3M]

I would never be rude on purpose.

Ok, but perhaps consider your wording a little because that is how your response came across.

 

[Onoff]

Now that's just plain rude! There are much better ways of approaching this, a PM for example.

He's not rude he's from Bristol!

All sorted via pm, all good.