slim_boy_fat
Member
- Messages
- 29,508
- Location
- Scottish Highlands
Tbh, I've never tried the remote which came with the heater. I have no logical reason for not doing so....
- Thread starter skotl
- Start date
Tbh, I've never tried the remote which came with the heater. I have no logical reason for not doing so....
Barking Mat
Cuddler of hedgehogs.
- Messages
- 13,517
- Location
- France, Brittany.
You must never just cut the current when they're running.
They must be turned off and allowed to do their cooling cycle.
I'd expect melting or fire risk otherwise.
mrsbruce
Member
- Messages
- 1,974
- Location
- Livingston, Scotland
I have one set up in the conservatory. It makes the conservatory useable in winter (I keep my big sewing machines in there), and adds an extra layer of warmth to the house on a very cold day. All run on a decent quality 12v power supply, and way cheaper than than using an electric heater.I have, on at least one occasion, had a ‘failure to start’ with the remote control fob. Not too important as I don’t need much heat to be OK-ish in the workshop.
BUT, I would not trust it to shut down from the remote control.Could cost me several litres of fuel! Anyway, I usually shut it off a while before shutting up the shop for the night. My air heater power-supply battery is usually back on ‘float charge’ before I exit.
I, yet, have the smaller heater to install in my car - but still not sure whether I should use it instead of burning gas, for heating the lounge this winter…
I did modify the fuel tank to draw the diesel from the top, as the bottom fittings have been known to loosen and leak, but otherwise standard.
Figure I may as well add to this thread.
After some deliberation, I've opted to buy an Afterburner controller for my heater (full details can be found at http://www.mrjones.id.au/afterburner/ )
However, I've also had to buy a new ECU (mrjones also supplies them), as some newer heaters are using a new ECU and control panel which use a different communication protocol.
So this collection got delivered a couple days ago-
A quick dismantle of the heater, and the old ECU is out -
New ECU on the left, and old on the right.
All the wiring/connectors are different places, but all the leads have plenty slack in them so that's not a problem.
All plugged in, new controller connected, temp sensor plugged in to the Afterburner, power connected, and we have power.
Press of the middle button, and we have ignition-
Now the main reason I wanted this, was for remote control.
After much fiddling on my phone (I should have taken a laptop out to the workshop!), I got the Afterburner connected to the wifi, so I can now control it via any browser connected to the wifi -
This obviously limits 'remote' control to within range of wifi, so now I need to configure a MQTT broker that can allow web access.
At the moment, I'm thinking Pi with NodeRed, and having NodeRed connecting to Arduino Cloud. Arduino Cloud is quite basic, but it will allow easy access via their phone app, which eliminates having to browse to a webpage, login, then click on links. Just open App, select correct Dashboard, and tap the on/off switch.
After some deliberation, I've opted to buy an Afterburner controller for my heater (full details can be found at http://www.mrjones.id.au/afterburner/ )
However, I've also had to buy a new ECU (mrjones also supplies them), as some newer heaters are using a new ECU and control panel which use a different communication protocol.
So this collection got delivered a couple days ago-
A quick dismantle of the heater, and the old ECU is out -
New ECU on the left, and old on the right.
All the wiring/connectors are different places, but all the leads have plenty slack in them so that's not a problem.
All plugged in, new controller connected, temp sensor plugged in to the Afterburner, power connected, and we have power.
Press of the middle button, and we have ignition-
Now the main reason I wanted this, was for remote control.
After much fiddling on my phone (I should have taken a laptop out to the workshop!), I got the Afterburner connected to the wifi, so I can now control it via any browser connected to the wifi -
This obviously limits 'remote' control to within range of wifi, so now I need to configure a MQTT broker that can allow web access.
At the moment, I'm thinking Pi with NodeRed, and having NodeRed connecting to Arduino Cloud. Arduino Cloud is quite basic, but it will allow easy access via their phone app, which eliminates having to browse to a webpage, login, then click on links. Just open App, select correct Dashboard, and tap the on/off switch.
mrsbruce
Member
- Messages
- 1,974
- Location
- Livingston, Scotland
I bought a feed pipe kit thing off amazon, and drilled a hole in the neck of the tank, just below the filler cap. Less chance of leakage (don’t ask me how I found that out).
mike os
just a little insane.....
- Messages
- 9,806
- Location
- North Wales
Well it’s installed … equipment is ok but the documentation is absolutely dire
Got this controller … if anyone knows how to set it please enlighten me
And what’s the red symbol? It’s permanently lit at the mo
Can’t set time or access settings … manual might as well still be in Chinese…
Long press up (left) enters a setting with xx:xx… time I guess? Adjust to time ok … then how to save? Wait does nothing, up/down adjusts … ok switches digit, hold exits without saving …
Don’t know how to access any other settings …
Got this controller … if anyone knows how to set it please enlighten me
And what’s the red symbol? It’s permanently lit at the mo
Can’t set time or access settings … manual might as well still be in Chinese…
Long press up (left) enters a setting with xx:xx… time I guess? Adjust to time ok … then how to save? Wait does nothing, up/down adjusts … ok switches digit, hold exits without saving …
Don’t know how to access any other settings …
Scalarocco
Smile, or I'll bite your leg...
- Messages
- 488
- Location
- Rossendale
That symbol is blue on mine. I thought it meant the electrical system (voltage) was functioning correctly.
mike os
just a little insane.....
- Messages
- 9,806
- Location
- North Wales
The implications are truly horrifying
gaz1
Member
- Messages
- 20,330
- Location
- westyorkshire
read what you put
as we have no idea what unit your using or any other details other than a photo as its near on impossible to search for something with no discription
James1979
Member
- Messages
- 8,418
- Location
- Orkney
Never seen that one before. I was intrigued.
Have a gaztube link
“Air diesel heater controller” was what I searched
gaz1
Member
- Messages
- 20,330
- Location
- westyorkshire
a reminder at the mods @Wozzaaah
when are you going to stop this trolling against a member
this is your own rules
Winding up other members (trolling)
Don't do it on any account. If it looks like you are deliberately trying to wind people up you'll quickly end up on the naughty step.
by a search @James1979 happens to be the biggest troll using the reference gaztube
stated gaztube all of the time other new members have no idea that the user means youtube isnt it about time it was directed correctly to the correct site
addjunkie
Member
- Messages
- 13,993
- Location
- Northumberland. Reet oot in the sticks
Needs to copyright the name quickly before someone else does!Gaztube….take it as a term of endearment, you are famous
James1979
Member
- Messages
- 8,418
- Location
- Orkney
Did that come with a heater?
I’ve not seen that one. My Chinese heater has the generic one that everyone has
Or else I’ve got the eber one in the pickup.
