Seadog
Save the planet. It's the only one with rum!
- Messages
- 13,071
- Location
- NE London - UK
Thanks.
- Thread starter Seadog
- Start date
Agroshield
Member
- Messages
- 6,397
There is a thread here that describes what the clutch does - if it is correct, it is an adjustable safety clutch that should slip when the tap is overloaded. Says it should be unlubricated.
www.model-engineer.co.uk
You might be able to select the material to cater for the tap sizes you want to use in the head: something closely approaching the original if you want to use it over its full capacity range; something less grippy if you only want to use it for tiny taps.
Another possible source: https://worldofwashers.com/product-category/washers/red-fibre-sheets/
404 | Model Engineer & Workshop Magazine
It looks like we've lost a piece!404: Page not found This page could not be found. Maybe try a search? If it's a forum topic you are looking for, ...
www.model-engineer.co.uk
You might be able to select the material to cater for the tap sizes you want to use in the head: something closely approaching the original if you want to use it over its full capacity range; something less grippy if you only want to use it for tiny taps.
Another possible source: https://worldofwashers.com/product-category/washers/red-fibre-sheets/
Matchless
I started with nothing, still have most of it left
- Messages
- 3,012
- Location
- Essex UK
It would not touch the bore so I left it, did not want to blunt it! just need to find itI'll pay you a visit in the not too distant, Pat. Have you used my MT3 reamer yet?
Seadog
Save the planet. It's the only one with rum!
- Messages
- 13,071
- Location
- NE London - UK
There is a thread here that describes what the clutch does - if it is correct, it is an adjustable safety clutch that should slip when the tap is overloaded. Says it should be unlubricated.
404 | Model Engineer & Workshop Magazine
It looks like we've lost a piece!404: Page not found This page could not be found. Maybe try a search? If it's a forum topic you are looking for, ...
You might be able to select the material to cater for the tap sizes you want to use in the head: something closely approaching the original if you want to use it over its full capacity range; something less grippy if you only want to use it for tiny taps.
Another possible source: https://worldofwashers.com/product-category/washers/red-fibre-sheets/
Great links Agro. None of my searches have turned up the instructions or red fibre sheet. But then I didn't search using that string
Seadog
Save the planet. It's the only one with rum!
- Messages
- 13,071
- Location
- NE London - UK
It would not touch the bore so I left it, did not want to blunt it! just need to find it
That's a bummer. It sounds like it needs to be ground in that case.
gaz1
Member
- Messages
- 20,547
- Location
- westyorkshire
404 | Model Engineer & Workshop Magazine
It looks like we've lost a piece!404: Page not found This page could not be found. Maybe try a search? If it's a forum topic you are looking for, ...
www.model-engineer.co.uk
old 2014 link
404 | Model Engineer & Workshop Magazine
It looks like we've lost a piece!404: Page not found This page could not be found. Maybe try a search? If it's a forum topic you are looking for, ...
www.model-engineer.co.uk
Vulcanite
Seadog
Save the planet. It's the only one with rum!
- Messages
- 13,071
- Location
- NE London - UK
404 | Model Engineer & Workshop Magazine
It looks like we've lost a piece!404: Page not found This page could not be found. Maybe try a search? If it's a forum topic you are looking for, ...
old 2014 link
404 | Model Engineer & Workshop Magazine
It looks like we've lost a piece!404: Page not found This page could not be found. Maybe try a search? If it's a forum topic you are looking for, ...
Vulcanite
Thanks Gaz. I'd found three of those links. The PDF is not the same model, unfortunately. But the discussion in the 2014 ME posting was interesting to read. I'm going to give KAL a call today, and if I draw a blank there I'll try Nuttall.
