For the swarfists

[8ob]

Bought a couple of these plunger magnetic gadgets.Great for cleaning up the lathe, mill and drills.

Bob

Pull the plunger and it all falls off

 

[BrokenBiker]

Feel like I need one of these for cleaning up behind the lathe

 

[8ob]

Feel like I need one of these for cleaning up behind the lathe

Link!

Bob

 

[BrokenBiker]

Link!

Bob

Ta much

 

[dieselsamurai]

Those things are great I first saw one at my friends about 10 years ago and they used to be £50 or so but so much cheaper now i use mine all the time you can even get one on wheels that you roll around like a broom then just release into a bin

 

[fizzy]

Bought a couple of these plunger magnetic gadgets.Great for cleaning up the lathe, mill and drills.

Bob

View attachment 526566

View attachment 526568

Pull the plunger and it all falls off

View attachment 526565

Yes I use mine a lot as well. Brilliant.

I have also bought one of these air duster blowers. Not as powerful as compressed air but awesome all the same. A lot handier if your compressor isnt always connected.

https://www.amazon.co.uk/GARAID-Compressed-150000RPM-Cordless-Keyboard/dp/B0FHX31YNQ/ref=sr_1_36?dib=eyJ2IjoiMSJ9.m9Ka0FBN4ea5CGc1SL-tsd7pWz5HROoT9mSN_gyHWTw5j6FI0VIOJVWhEVltPR3vbEJRaAL9BuhYyxxUHOfg5snHd5FC6PCH2eFonXabB5dzEDOOpBg8VV9Um5P9iBAX7q6sBoZ7lu4miy4jomm1-q9x_y0MVm6NUa2n6Rx6ekBuxilS84aMNTXr4k4zLKW6AFc0mia_gCk3ZMCHS4P7wqjVMSsI72Eq14nyeIcsvqC9r_WCpqFmX5Qsu4y_bgvQv-5Wu1vbQ0-hXzOE58PvMMXthVHALvqAc9ClEIBqgXQ.3Kgxc7Brem1dtg2GVyekbt787k3vxeP6S-p4L53FnZ4&dib_tag=se&keywords=air+duster&qid=1768323146&sr=8-36

 

[zzr1200]

Link!

Bob

Snap, mine turned up on the 7th Jan, yet to try it out.....

Appears to be much better build than my old one (Evolution).

I purchased from an English supplier many years ago....

 

[Pete.]

I set mine on the mill alongside the horizontal cutter and it pulled a lot of the cast iron chips away as it was cutting.

Such a simple tool but so very useful too.

 

[6ply]

Link!

Bob

This is what I got when I followed Bob's link. Bob, is this what you paid?

 

[whm_fab]

Great, I went into temu to get this, now I’ve 45 quid worth of ****e on its way, thanks !

 

[8ob]

This is what I got when I followed Bob's link. Bob, is this what you paid?

Seem to have gone up a bit. This is what I paid to the same seller.

Bob

 

[Screwdriver]

 

[JEZGUZ]

Put a plastic bag over the wand, when you.ve collected all the swarf turn it inside out over the swarf and switch off the magnet, swarf contained in the bag.

 

[henry Kadzielski]

I have two wands (one long one and one short, also the broom) as I have two boys, again one long one and one short(er). This way they have one each and can't get it wrong. Both have filled formal complaints about the operation of these wands, they don't work. They will not pickup alloy or stainless swarf. I have been told to get them fixed as they should be under warranty

 

[smashweld]

never ordered from temu but think this might be my first order
usually just blast it all off with the airline (being cautious) and sweep it up off the floor, although half of it seems to vanish

 

[sako243]

Do they do one for aluminium?

 

[iNf]

Do they do one for aluminium?

Bet they sell loads for aloominum

 

[zzr1200]

Do they do one for aluminium?

Yep.....

https://www.heyduggee.com/products/sticky-stick-stick-singing-plush-toy/

 

[Blue Chips]

Very handy tool. I bought mine years ago, but can't recall what it cost. I used it about 10 minutes ago to clean up the swarf on my lathe. Not so handy for certain stainless series, of course.

 

[oldbikedavey]

I could get quite interested in one of those devices......