Stuff you have made today

[RichardM]

Made another one with more clamp screws, also the adjuster nuts.


Bearing bar made, may look for some smaller bearings, but these are what I have in my "stock".


Just need the boring bar holders finishing.

 

[Tupers]

Paint on, masking off!

 

[cheb]

Made another one with more clamp screws, also the adjuster nuts.
View attachment 493712

Bearing bar made, may look for some smaller bearings, but these are what I have in my "stock".
View attachment 493711

Just need the boring bar holders finishing.View attachment 493713

What's the bearing bar for please?

 

[Olderisbetter]

Just the grouting and a few bits left to do

 

[RichardM]

What's the bearing bar for please?

Truing up stock in the chuck easily.

 

[redlig]

Just the grouting and a few bits left to do View attachment 493750

Just be sure you locate the toilet roll holder within easy reach when seated .

 

[cheb]

Truing up stock in the chuck easily.

Thanks. Another thing added to the list.

 

[Dev]

Made another chair using up the bit of trailer ply I wanted to use the last of.
Easier to finish - only the edges need sealed .
I would’ve had enough except for some manufacturing issues (machine operated by incompetent user)

 

[Seadog]

Just be sure you locate the toilet roll holder within easy reach when seated .

A free-standing one would be what I'd go for, since there's no side wall to put one on.

 

[redlig]

A free-standing one would be what I'd go for, since there's no side wall to put one on.

Perhaps a "Dial a Wipe " is going to be installed.

 

[badabec]

Just the grouting and a few bits left to do View attachment 493750

Bath taps?

 

[Olderisbetter]

Just be sure you locate the toilet roll holder within easy reach when seated .

That will be fixed to the wall on the left of the toilet after the grout is done

 

[Olderisbetter]

Just be sure you locate the toilet roll holder within easy reach when seated .

That will be fixed to the wall on the left of the toilet after the grout is

Bath taps?

They will be fitted after grouting and silicone is done, it saves them being in the way.

 

[Memmeddu]

Had very little time to reply on the various threads I'm used to.
Anyways on Wednesday my 3/4" failed it's dead, I have to disassemble and figure out what actually happened looks like there's no power coming out of the PCB.
Not even the LED light works, but the PCB panel lights on, maybe just the switch?
I'll try to find an original brushless Makita 3/4" PCB and switch, hoping it will be possible to implant it on the yofidra clone, but surely having to switch to original Makita LXT battery packs because they have a communication terminal need to enable the PCB.
TIG welder arrived on Wednesdays so I have unboxed it and plugged in to check if it works.
Went through parameters and everything should be ok
Have to test it yet.
Moved stuff in my storage room to make a little space to fit the Tig.
No welding helmet included.
I want to try it out before the feedback.

On yesterday I went to my local airsoft field and tested my M4A1, connected a 7.4V lipo, it spins fine very quiet but it didn't chambered any BB so it has been not possible to chronograph it.
So I still not know if it respects our regulations (1 joule in Italy) and so if it's legal or not.
On this morning I've disassembled it again and discovered it was both a delayer and hop up issue.
So I've replaced parts and tested it again at home using a 12V battery.
And It actually throws BBs .
New Chrono test on Sunday afternoon.
And actually ordered a new hop up

 

[Seadog]

That will be fixed to the wall on the left of the toilet after the grout is done

For me that's a ridiculous position.

 

[cheb]

For me that's a ridiculous position.

You'll have to use your own toilet roll then.

 

[Farside]

Perhaps a "Dial a Wipe " is going to be installed.

A pound per sheet?

 

[Olderisbetter]

A pound per sheet?

Lock down prices

 

[redlig]

A pound per sheet?

who pays who?

 

[ajlelectronics]

Machine Mart temporary garage. 2-3 people required apparently. As nobody was interested in helping, I did it myself.

Instructions not good, especially in regard to measurement points and securing the cover.

It was also damaged out of the box.