Stuff you have made today

[wyn]

Made a "grippy/turny" thingy for my thermal imager.
I lost the original the other night and trying to focus the thing was a nightmare.
Just a bit of 6082 with a 4mm clamping bolt.
Blasted it with some aluminium oxide and chucked a bit of paint on.
It's a much larger diameter which makes it easier to find/turn but needs a new lens cap.

 

[toddy]

i have been giving wood carving a good....
yes i know it is not metal...
this is my second piece.

 

[Welderpaul]

Half size railway signal... might turn it into a coat rack. Might not.

View attachment 274631

Oh, looks different that way round

 

[Barking Mat]

Burnt & ******** is the only way.

I don't want to try your shortbread.

 

[Hitch]

Oh, looks different that way round

Droopy.

 

[Memmeddu]

Yesterday ive been working on a jobsite , 50km travel , went there , started doing but couldn't do anything .
I needed to switch the power off but they had to work so I couldn't and didn't work
Spent an entire morning there ,no money
-10 euros for gasoline .
-5 hours of my life nobody can give me back .
I'm tired of this jobsite , I've to finish it , but customer is avoiding me to work .
I can't work in those conditions.

Today went to buy firewood , loaded the car and once home discovered that seller put only big logs in the trunk.
Took the chainsaw ,the axe, a wedge and a sledgehammer.
Done myself .
Chainsaw failed ,still have to understand what happened.
Axe edge ruined

Replaced a mirror on my sister's Toyota again

Tomorrow another jobsite in the morning .
And plasma demolition of a concrete mixer in the evening .

I'll have to borrow the plasma cutter from a friend tomorrow afternoon

 

[redlig]

With all you guys treating their wives I got an attack of the guilty feelings. I knew no good would come of this site. So I made one of these for her . Confused her on 2 fronts,why and what, and couldn't guess what it was for .. Can anyone out there make a guess? Hint its for the kitchen . What else does one give the missus.

 

[Cobbler]

Spaghetti helping measuring gauge?

 

[Barking Mat]

Sausage chopper?

 

[brewdexta]

Donut hole gauge?

I remember Johnny Craddock wishing that the audience's donuts should turn out like Fanny's

 

[DAPPH]

View attachment 274490

Bending some alu sheet for a pcb enclosure. Vice bender put plenty of scratches into the annodising and I need a removable way of bolting the vice to lathe bench.

Also swept the floor - I know where everything is, and it wasnt in the bit I swept! (Dropped some inserts last week )

After I spent an hour or three making a tiny ANF screw and dropped the sodding thing , then spent two days cleaning out the garage to find it I decided that it might be wise to slip lengths of timber or three inch round down pipe under the front of each wheeled work bench & chock it so it would stay tught up tothe front castors . So that anything I dropped would stay within the walkway areas in front of the benches ..all I had to do was trail a big toroidal magnet inside a poly bag on a length of string and " Hey Presto ) it finds it for me if it's iron based. Have resorted to the old vax tub cleaner to find alu & brass .

That tiny steel screw .....
I couldn't find it anywhere not even after vacuuming the whole floor in yard squares , checking the cloth dust bag after each square before putting everything back . I found it by chance stuck in a crevasse of the light concrete block walling some 18 inches up from the ground nearly 2 foot from where I dropped it.
It must have been one of the big garden spiders that did it .

 

[MattF]

Sausage chopper?

That's what I'm fearing she may use it for.

 

[DAPPH]

Today I made a reel for rolling out and probably more importantly, rolling back in 100m of 2 inch lay-flat hose.

View attachment 274540

Rough and ready.
It's made out of stuff I had kicking about, scaffold tube, 8mm re-bar, scaffold jack leg and plastic from a damaged fender.
I'll see if it works next week.
I used one of @pressbrake1 steel welding squares to hold the bits in place for tacking and a set of rolls I got on here for bending the re-bar for the drum..

View attachment 274541

I might even give it a lick of paint, not to protect it, but to see if I can lower the chances of it being thrown in the scrap skip while it's still needed.

Paint it pink or dandelion yellow then

 

[DAPPH]

That's why I've never done it before but I reckon making ten at a time I could do them a bit quicker. Would probably save a bit of time starting with annealed sheet rather than 22mm water pipe too.

View attachment 274602View attachment 274601

Just had a thought, there's probably money doing metal versions of trendy houseplants, people sell cuttings, literally single leaves, for upwards of fifty quid because they're slightly more variegated than the plant usually is!

An eternal valentines rose to tell her you always love her and your such a tight wad that buying her one now will save you a small fortune in the future.

 

[MattF]

Paint it pink or dandelion yellow then

Not pink. I used to take pink rubble tubs on site, thinking that no bloke in his right mind would "borrow" them. They drew them more than any other colour.

 

[Barking Mat]

Paint it pink or dandelion yellow then

Paint everything yellow, then you can't lose it or fall over it.

That's my logic.

 

[The_Yellow_Ardvark]

Paint everything yellow, then you can't lose it or fall over it.

That's my logic.

When will that start?

 

[badabec]

My Mrs. Was pretty happy.

View attachment 274588

Wikus van de Merwe (Sharlto Copley) does them with his bare hands in the film District 9

 

[badabec]

Half size railway signal... might turn it into a coat rack. Might not.

View attachment 274631

'Occupied' sign for the toilet?

 

[Barking Mat]

When will that start?

It's started, it may never finish.