Honda S2000 turbo manifold, exhaust.. etc build

[vtec_lude]

nice pipes, i have question no welding related honda engines do they all fit the rwd gearbox

Sorry I'm not understanding your question. Read it a few times but still clueless.

 

[rusty69bus]

sorry bad grammar. i'm looking at an engine swap in one of my cars thats rwd and i was considering a honda engine but i don't know enough about them to know if honda engines are a striaght swap onto honda gearboxes.

 

[vtec_lude]

I don't think they are a straight swap. You might be able to get certain adapter plates so you can use a honda H engine with a honda B Gearbox.

 

[rusty69bus]

ok, ta the search continues

 

[Wozzaaah]

Sorry I'm not understanding your question. Read it a few times but still clueless.

sorry bad grammar. i'm looking at an engine swap in one of my cars thats rwd and i was considering a honda engine but i don't know enough about them to know if honda engines are a striaght swap onto honda gearboxes.

That's better!

Tempted to bung a meaty motor in the Morris then Rusty?

Very nice work Vtec, that really does look superb

 

[rusty69bus]

no actually, thinking of smallish engine better not hijack this thread maybe you can use your new powers and move this to the brew room

 

[Robotstar5]

Nice bit of welding

I Well after 20hrs of welding it's pretty much done now. I think I need a lie down.

How many hours linishing required now?

 

[Iain Westland]

very enjoyable, must be my age but with an internet full of porn i enjoy looking at very high quality fabrication jobs instead



Iain

 

[madkayaker]

very enjoyable, must be my age but with an internet full of porn i enjoy looking at very high quality fabrication jobs instead



Iain

Same here

 

[Archie]

You make it sound like it's a one or the other situation....

 

[zardoz]

Thats some fine pipe welding there! I dont know if anyone here went to the classic car & Bike show at the NEC a few weekends back? There was a Yamaha Trials bike with an exhaust with twin ports. It had been welded up from approx 30 sections for each pipe. most of the sections only an inch or two long, with some great TIG welds (or neat MIG) I forgot to take a picture, so engrosed was I with marvelling at this excellent piece of engineering. I was so peed off when i realized i had no picture, as i had over 160 pics of allsorts, but not that. Did anyone else go and see the same bike ? (or take a pic?, that would be too much to hope for though)

All i know about the guy that did the welding is that he has moved to the Czech republic now, but will still do exhausts by return post if you send him some blueprints!

 

[Robotstar5]

I suppose you could could class silicon implants as "fabrication jobs", don't know wether it would work as an excuse?

 

[madkayaker]

more body work i think

 

[marknotgeorge]

Have I missed summat again?

 

[Rick]

I'd have used a stainless elbow into the cooler, those silicon bends look and flow badly.

 

[JayRS4]

Whats the car Rick, can`t quite tell from the headlight

 

[Rick]

Whats the car Rick, can`t quite tell from the headlight

Its the S2000 from the first page of this thread. Come on you should know this from the crash bar haha.

 

[JayRS4]

well there`s me being dumb then, must be the christmas spirit kicking in *hic*

 

[bucko]

That’s way to nice for an oily engine bay I think it should sit on my dining room table as a centre piece

at what point dose engineering become art

 

[madkayaker]

When it lookes better than the Ikea" furniture