DAF 45 question

[Tinbasherdan]

oh mighty forumers, another weird question brought to you from my fevered mind: does anyone know, or have access to the parts list to get, the fitting size and type for the hydraulic line into the air assisted clutch slave cylinder? googled all different kinds of words and nothings jumping out at me.
dont need the full line as the slaves being mated to a series 3 LR brake master servo, so i need to have a line made up specially!

cheers
dan

 

[Rig Pig]

Can you post some photos + measurements of the ports?

 

[Tinbasherdan]

I could, if it wasn't in Devon it's being brought up next week by a mate, if it was here it'd be easier for me :/

 

[8ob]

Mine is in the workshop so here is a snap of it, air in the top and a 10mm banjo in the bottom.

Bob

 

[Tinbasherdan]

Legend! Knew someone would be able to answer is that m10 thread?

 

[Tinbasherdan]

Is that the zf box and 6bt engine?

 

[8ob]

Is that the zf box and 6bt engine?

Yes 10 ton daf 45 with zf and 6bt, I will check the thread tomorrow. There is a 7.5 tonner festering at my other yard that has a spicer box so if the zf version is wrong I can check the other one out.

Bob

 

[Tinbasherdan]

Yes 10 ton daf 45 with zf and 6bt, I will check the thread tomorrow. There is a 7.5 tonner festering at my other yard that has a spicer box so if the zf version is wrong I can check the other one out.

Bob

Nope it's the zf I'm after what's happening with the 6bt and spicer? May be after one

 

[waldershelf]

Clutch, air assisted WTF? then I realised you didn't mean one of these :------

 

[rtbcomp]

^^ I was thinking of those silly little "Daffodil" cars with Continuously Variable Transmission.

 

[waldershelf]

^^ I was thinking of those silly little "Daffodil" cars with Continuously Variable Transmission.

So was I but my picture didn't come thru, sorted.

 

[armalites]

A mate of mine is putting a 6bt and ZF into a 110.

 

[normspanners]

dont need the full line as the slaves being mated to a series 3 LR brake master servo, so i need to have a line made up specially!

why would it need to be servo and air assisted ?

 

[Tinbasherdan]

why would it need to be servo and air assisted ?

Master cylinder my mistake

 

[Tinbasherdan]

A mate of mine is putting a 6bt and ZF into a 110.

Exactly why I'm asking

 

[normspanners]

^^ I was thinking of those silly little "Daffodil" cars with Continuously Variable Transmission.

Ha imagine one of those engines in a 110???
in fact I could------- as the donkey starting engine------ a little like the cat dozers used to use

 

[8ob]

Legend! Knew someone would be able to answer is that m10 thread?

I measured it today and its 7/16 unf on the thread of the banjo bolt.

Bob

 

[Tinbasherdan]

I measured it today and its 7/16 unf on the thread of the banjo bolt.

Bob

Spot on fella thanks! I sent you a pm I don't know if you got it

 

[8ob]

Got that, there is a complete 6bt engine on the floor, its the 130 turbo I just need to check the gearbox situation. Or there is a complete setup in a truck if you fancy coming down to remove it. That will give you the chance to hear it and rob any other bits you want off the vehicle, lifting gear is here so just bring tools.

Bob

 

[Tinbasherdan]

What would you want for it, and I won't be in a position to collect for a couple of months or so if it's a desperate situation to move it don't worry about it