Barking Mat
Cuddler of hedgehogs.
- Messages
- 13,515
- Location
- France, Brittany.
I'm more in cardboard template land.
- Thread starter God mode restorations
- Start date
Onoff
In the land of the unfinished project I am King!
- Messages
- 12,970
- Location
- Sevenoaks, UK
Their cobalt hole saws are the best I've ever used.
Gritineye
Member
- Messages
- 2,100
Never had much luck turning stainless, but must have got lucky with one of the drops from my friendly scrappy.
Needed a screw in plug for a the end of a stainless pressure vessel. I have no reliable means of measuring the internal thread, so I just used inside callipers to get some idea.
Well the special helpful perfection seeking gods must have been sitting on my shoulders, because when I thought I must be getting close, I took it out of the lathe for the first time and it was a perfect fit, phew !
Needed a screw in plug for a the end of a stainless pressure vessel. I have no reliable means of measuring the internal thread, so I just used inside callipers to get some idea.
Well the special helpful perfection seeking gods must have been sitting on my shoulders, because when I thought I must be getting close, I took it out of the lathe for the first time and it was a perfect fit, phew !
Gritineye
Member
- Messages
- 2,100
Last edited:
Kram
Member
- Messages
- 8,064
- Location
- Sussex
Amazon magnets fitted. Individually they lift about 1.6kg and the combination is over 5kg. Not glued, fitted a steel 3mm plate the other side for them to stick to. With it almost done, I've had a better idea.
39mm bore, 43mm deep.
I have not decided if I will cross drill and pin to seperate the sizes, and to work out where to fit the collet holder pins.
Maker
Most folk just call me; Orange Joe
- Messages
- 10,633
- Location
- Keeler crater
A pair of bracket things. 40x8mm flat, cut the radius on the end with a massive rasp from Hotponyshoes, went surprisingly quickly.
Here they are fitted, the side gate shuts against it. I put the post up about ten years ago with a line of Rawl plugs, didn't think to offset the screws so every time the gate slams it levers the plugs out, these brackets offset the screw as far as possible. I've also swapped Rawl plugs for M10 stud and Fischer resin so there's no pulling them out anyway.
Here they are fitted, the side gate shuts against it. I put the post up about ten years ago with a line of Rawl plugs, didn't think to offset the screws so every time the gate slams it levers the plugs out, these brackets offset the screw as far as possible. I've also swapped Rawl plugs for M10 stud and Fischer resin so there's no pulling them out anyway.
Olderisbetter
Member
- Messages
- 3,936
- Location
- Wolverhampton
This was a bit of spare time and bits sitting around
Last edited:
What's spare time?
Bullet2012
Member
- Messages
- 5,365
- Location
- on average about 200 miles from the ISS.
Time spent posting 12k plus responses on a website.
Lewis_RX8
Member
- Messages
- 1,571
- Location
- Scotland
MattF
Forum Supporter
- Messages
- 17,894
- Location
- South Yorkshire
Ouch, Need to get some stats on here whos got the most hours etc
C'mon, we all know brightspark would be top of the list.
Hood
I am obsessed.
- Messages
- 17,778
- Location
- Carnoustie, Scotland
Bit more done to the trailer.
All the box and hubs welded on.
The final vertical weld.
Flipped it over as normally I don't mind doing overhead welds but in stainless I was not so keen especially as I would be having to lie down directly under it and stainless is runny
I got all of the frame welded underneath and only have some eye bolts to weld on but that will be tomorrow.
Vid of a vertical weld, slag eventually came off after it cooled
All the box and hubs welded on.
The final vertical weld.
Flipped it over as normally I don't mind doing overhead welds but in stainless I was not so keen especially as I would be having to lie down directly under it and stainless is runny
I got all of the frame welded underneath and only have some eye bolts to weld on but that will be tomorrow.
Vid of a vertical weld, slag eventually came off after it cooled
Olderisbetter
Member
- Messages
- 3,936
- Location
- Wolverhampton
Spare time is the gap i have between rubbing my aching bits with voltarol and it taking effect
Hood
I am obsessed.
- Messages
- 17,778
- Location
- Carnoustie, Scotland
You must be a masochist, I would never rub my bits with voltarolSpare time is the gap i have between rubbing my aching bits with voltarol and it taking effect
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 20,332
- Location
- Going Away.
Spare time is the gap i have between rubbing my aching bits with voltarol and it taking effect
Is that before you change hands after 99?You must be a masochist, I would never rub my bits with voltarol
Maker
Most folk just call me; Orange Joe
- Messages
- 10,633
- Location
- Keeler crater
I'll never forget having a wee after applying Deep Heat!You must be a masochist, I would never rub my bits with voltarol
The_Yellow_Ardvark
https://www.death-clock.org/
- Messages
- 20,332
- Location
- Going Away.
I could tell you about the time a "person who self abuses himself" was found helping himself to my tools.I'll never forget having a wee after applying Deep Heat!
A nice helping off deep heat to his pot of Haemoid cream.
Barking Mat
Cuddler of hedgehogs.
- Messages
- 13,515
- Location
- France, Brittany.
Ooh soo many questions...Bit more done to the trailer.
All the box and hubs welded on.
View attachment 315400
The final vertical weld.
View attachment 315402
Flipped it over as normally I don't mind doing overhead welds but in stainless I was not so keen especially as I would be having to lie down directly under it and stainless is runny
View attachment 315401
I got all of the frame welded underneath and only have some eye bolts to weld on but that will be tomorrow.
Vid of a vertical weld, slag eventually came off after it cooled
Is that a slight up and down weave?
What's with holding the chisel to it ?
To dissipate heat ?
316L or other flavour.
Surprised how much rod you put in for such a short bead.
Nice welding.
