Hood
I am obsessed.
- Messages
- 17,977
- Location
- Carnoustie, Scotland
They have not been fitted yet
- Thread starter God mode restorations
- Start date
Hood
I am obsessed.
- Messages
- 17,977
- Location
- Carnoustie, Scotland
You jest but I heard that has been done to the mast that h
Oh but they don't damage the sea bed they say. Funny thing was when I worked on a creel boat fishing around about the Bell Rock grounds we were getting 25-30 boxes of crab a day, the first clammers that came round this way and the next day we had 15 boxes of whole crab and 5 boxes of damaged crab with holes in their shells. After that if we two boxes we were doing well, 20 years later it has only just started to improve.
Oh but they don't damage the sea bed they say. Funny thing was when I worked on a creel boat fishing around about the Bell Rock grounds we were getting 25-30 boxes of crab a day, the first clammers that came round this way and the next day we had 15 boxes of whole crab and 5 boxes of damaged crab with holes in their shells. After that if we two boxes we were doing well, 20 years later it has only just started to improve.
Hood
I am obsessed.
- Messages
- 17,977
- Location
- Carnoustie, Scotland
A few more pics for your delight, I reckon between me and @Tangledfeet we are doing a cracking job of the stick welding 
Tangledfeet
Knurling is my Nemesis.
- Messages
- 3,221
- Location
- Top of a hill above St Andrews, Fife
John kohlman
New Member
- Messages
- 2
- Location
- Edmonton, Alberta, Canada
Clearly not a ticketed welder. But if I am wrong and this guy should have his ticket pulled and sent back to school. That is an embarrassment.
John kohlman
New Member
- Messages
- 2
- Location
- Edmonton, Alberta, Canada
Is that suppose to be funny. Maybe he should learn how to weld and fix it properly. Or is he trying to kill somebody?
mrsbruce
Member
- Messages
- 1,969
- Location
- Livingston, Scotland
Hood
I am obsessed.
- Messages
- 17,977
- Location
- Carnoustie, Scotland
He may well have a ticket but I think it will be for parking.
mtt.tr
Member
- Messages
- 8,464
- Location
- Essex/Suffolk border
Hood
I am obsessed.
- Messages
- 17,977
- Location
- Carnoustie, Scotland
It is not a first go.
It is not in service yet but it will be at some point.
mtt.tr
Member
- Messages
- 8,464
- Location
- Essex/Suffolk border
Hood
I am obsessed.
- Messages
- 17,977
- Location
- Carnoustie, Scotland
That is one way of putting it
mtt.tr
Member
- Messages
- 8,464
- Location
- Essex/Suffolk border
That is one way of putting it
I commend the bravery, take the Russian approach i"will only kill you if you think it will kill you"
Tangledfeet
Knurling is my Nemesis.
- Messages
- 3,221
- Location
- Top of a hill above St Andrews, Fife
Roof vent on the container, proper scrapheap challenge job from offcuts. Welding is rough as so don’t zoom in too much 
think I got it waterproof though the next shower will answer that one. Need to fit some seals on it.
It started off as what was going to be a roof light as I had some offcuts of polycarbonate sheet but it didn’t let much light in cue it being transformed into a vent.
A lash up of 50x3mm flat bar, 10mm square bar, some 3mm sheet and some 30x30 angle.
Currently in the process of fitting the 15inch vortice fan to the other end to drag a lot of air through.
Topside open
Underside closed
Topside in stealth mode
think I got it waterproof though the next shower will answer that one. Need to fit some seals on it. It started off as what was going to be a roof light as I had some offcuts of polycarbonate sheet but it didn’t let much light in cue it being transformed into a vent.
A lash up of 50x3mm flat bar, 10mm square bar, some 3mm sheet and some 30x30 angle.
Currently in the process of fitting the 15inch vortice fan to the other end to drag a lot of air through.
Topside open
Underside closed
Topside in stealth mode
