frank horton
V twins are great but 4"s rule.........
- Messages
- 3,852
- Location
- Crete, Greece
peeing of rain so catching up with tasks.......
please note have at least 10x 3phase machines from 1/5HP to 5HP.....
will need the above but suitable for 15hp'ish..that gives me plenty of safety.......prob x 30% over the norm I guess for my motors....?
my biggest motor is 415x5HP, I know it will take at least 3 times that for start up...???? ..I will only use one machine at a time.....
I do use an Oil filled Oxford welder, 225amp max, thats suitable for either voltage..would like to get it back on 3Phase as its rubbish on single phase over 160amp...will the DPC handle it.....?
I will sell my 5.5HPx415 compressor for a big'ish 240v one as I'm worried if the compressor starts up when I'm useing the car lift.....
have given it some thought but I don't know enough about this Black Art........
looked on ebay prices start from, Korea 20hp x £520
the next is a uk supplied but prob not buit in UK for 15hp x £1500.......
I have a 40amp supply direct from the board....poss 45amp....too wet to go look.....
such a big difference in cost, dont wanna buy DPC made in China giving that much money away to a UK stockist...if I went to Korea direct I could buy 3 for the same money .....not botherd about the warrenty after a few years.....
norm I would look for recomends etc on their stuff but u cant believe anything now.....
is there anything I should look for......
I'm guessing they all have thermal cut outs and override/overload RCD/fuses etc.....plus something if a phase goes down........
I really dont know and dont wanna mess up when spending this much money on an electronic WIZZ BANG.....
ps.. I have 3phase on a pole 10m from my incoming fuse board but the elec comp want €12,000 euros to supply a new cable and meter x 415v.......yes, no mistake €12,000.......they can swivel if u know what I mean....
any suggestions.......please.......
please note have at least 10x 3phase machines from 1/5HP to 5HP.....
will need the above but suitable for 15hp'ish..that gives me plenty of safety.......prob x 30% over the norm I guess for my motors....?
my biggest motor is 415x5HP, I know it will take at least 3 times that for start up...???? ..I will only use one machine at a time.....
I do use an Oil filled Oxford welder, 225amp max, thats suitable for either voltage..would like to get it back on 3Phase as its rubbish on single phase over 160amp...will the DPC handle it.....?
I will sell my 5.5HPx415 compressor for a big'ish 240v one as I'm worried if the compressor starts up when I'm useing the car lift.....
have given it some thought but I don't know enough about this Black Art........
looked on ebay prices start from, Korea 20hp x £520
the next is a uk supplied but prob not buit in UK for 15hp x £1500.......
I have a 40amp supply direct from the board....poss 45amp....too wet to go look.....
such a big difference in cost, dont wanna buy DPC made in China giving that much money away to a UK stockist...if I went to Korea direct I could buy 3 for the same money .....not botherd about the warrenty after a few years.....
norm I would look for recomends etc on their stuff but u cant believe anything now.....
is there anything I should look for......
I'm guessing they all have thermal cut outs and override/overload RCD/fuses etc.....plus something if a phase goes down........
I really dont know and dont wanna mess up when spending this much money on an electronic WIZZ BANG.....
ps.. I have 3phase on a pole 10m from my incoming fuse board but the elec comp want €12,000 euros to supply a new cable and meter x 415v.......yes, no mistake €12,000.......they can swivel if u know what I mean....
any suggestions.......please.......