Stuff you have made today

[henry Kadzielski]

How was the steel sheet bent along the radius? MIG welding?

The sheet, I think you are referring to is the inner skin of the tank. It was bent at about 40mm spacing on a press brake at a predefined angle. I didn't do the bending, though I did help hold and push it in. The welding is via mig and Francesca (Fronius TPS320i) did the welding using .8mm 316L with 98 gas (98 % argon 2% Co2). Francesca has PMC and LSC and I think both are operating. I say think as I don't know what the difference is without them operating. When I got Francesca she had it all there, one of the Fronius guys set it up and said try that, it welded ok so I have left it and never played with it. AS I progress I will take some more pics and post them.

thats a lovely looking pizza oven! its huge!

I can actually see where you got that from

 

[DAPPH]

You've lost me there... bolt action, what was asked for.
The only twist mechanisms that seem to fail are the 7mm slimline ones. I don't tend to use them.

Same thing you call bolt action I called click locks yep the slim line 7 mm are starting to show wear after seven years of daily use and rotate under the slightest pressure .
Can't really grumble , looking forward to using some donated spalted beech to make a lot of new ones for friends if it turns out to be suitable ( ripe / rotten in places and riddled with worm and bug tunnels )
Cut up a slab of the beech 4x16 x 16 " ish earlier today into 3/4 inch square blanks by 16" long along the grain . Struggling to find any sound turnable wood from it at present . Got plenty more to play with over then next week or so .
I baked what I cut at 120 oC inthe oven for three hours to kill off the spalt causing spores and any eggs of creepies still in the blanks .

 

[Farside]

I made or rather remade a VW samba picture on a rock i was given, it did have a picture on but it was peeling off so i re did it like a rusty old bus which i think looks better.
View attachment 395831

Bloody huge spud!

 

[Hitch]

The 10mm socket you can never find.

 

[nickk]

Been fitting extra stability jacks on two of these mobile shower trailers.
Improvement on the steps is next on the list.

 

[Richiew]

A pallet breaker. I think I've found a handy local supply so I thought it was finally worth making one.

All made from bits found in the garage, A-Team style.

40mm scaffold pole. I ground off the galv. The end was coped as I already had a nice tool to use. My nearest holesaw was 38mm though, so I might as well have just used the grinder from the start as it all needed opening out. The steel seems really nice to cut, Google suggests it is EN39.

Excuse the mess. This is getting sorted soon/

The prongs are 10mm bar, I think 60mm wide. The gap between the two is a little wider than two inches.
Stick welded at 129 amps using my Sherman/Jasic welder. 3.2mm 6013.

Didn't get the galv off the inside and it shows. Have to be careful.

I didn't quite get the handle angle right. It is a little too upright. The tool is very heavy but strong, my back will wear out before the tool does. It works very well and dismantles the pallets quietly and effortlessly. Damage to the wood is much reduced should I want to use it for something other than fuel.

I can still use the other end to break ratchets, sockets and breaker bars so that's a win too.

 

[Hopefuldave]

A huge puddle of torch coolant on the floor, followed by a mound of blue soggy sawdust... Had to pull the cooler out and pull it to bits looking for the leak (a hose pushed off its spigot, remedy the ClampTite-alike)

Dave H. (the other one)

 

[striker]

A pallet breaker. I think I've found a handy local supply so I thought it was finally worth making one.

All made from bits found in the garage, A-Team style.

40mm scaffold pole. I ground off the galv. The end was coped as I already had a nice tool to use. My nearest holesaw was 38mm though, so I might as well have just used the grinder from the start as it all needed opening out. The steel seems really nice to cut, Google suggests it is EN39.

Excuse the mess. This is getting sorted soon/

View attachment 396090


View attachment 396091

The prongs are 10mm bar, I think 60mm wide. The gap between the two is a little wider than two inches.
Stick welded at 129 amps using my Sherman/Jasic welder. 3.2mm 6013.

View attachment 396092



View attachment 396093

View attachment 396094

Didn't get the galv off the inside and it shows. Have to be careful.

View attachment 396095

View attachment 396096
View attachment 396097View attachment 396098

I didn't quite get the handle angle right. It is a little too upright. The tool is very heavy but strong, my back will wear out before the tool does. It works very well and dismantles the pallets quietly and effortlessly. Damage to the wood is much reduced should I want to use it for something other than fuel.

I can still use the other end to break ratchets, sockets and breaker bars so that's a win too.

Good job. Could you pie cut near the bottom of the handle and weld up to get a better handle angle if it's a little out?

 

[Richiew]

It's fine as it is, really. I had a chance to correct it after tacking up and testing for ergonomics but couldn't be arsed then, so there's no hope now.

 

[Tupers]

its not finished and painted

I haven’t decided on a colour yet I’m stuck between Java green and Signal red.

I have added some legs to the tool tray and stops to the lid so the latches can lock down tight though.

 

[Robotstar5]

A pallet breaker. I think I've found a handy local supply so I thought it was finally worth making one.

All made from bits found in the garage, A-Team style.

We used a Rollpacker to dismantle the pallets at work, only good for firewood after.

 

[sako243]

A battery, never had a DIY one before...

After that installed it into a neighbour's quad and it fixed the trouble starting and shifting gear.

 

[Robotstar5]

A battery, never had a DIY one before...
View attachment 396133
After that installed it into a neighbour's quad and it fixed the trouble starting and shifting gear.

I thought they'd stopped sending out separate acid packs a while ago?

 

[sako243]

I thought they'd stopped sending out separate acid packs a while ago?

Apparently not. Although this came via a local tractor factors so perhaps they were meant to do it.

 

[RichardM]

Maybe different for tractors / business to business as opposed to business to consumer. My last one for the bike came pre-filled.

Important UK Announcement: New regulations will change the way motorcycle batteries can be sold - Yuasa

From July 1st 2018 all motorcycle batteries must be filled by the retailer before being sold to a member of the public in the UK who does not possess a…

www.yuasa.co.uk

 

[sako243]

Funnily enough it was a Yuasa battery. Shows instructions aren't idiot proof though - so many languages on the sheet. Proper procedure was fill, leave to vent, seal, charge. Not what I did which was fill, seal, swear, debate whether I can get away without venting, carefully (and successfully) remove the seal without damaging it, leave to vent, seal again, charge.

 

[nickk]

Back in the ‘90’s I had a BMW motorbike battery in the post,from BVM I think,it came with separate bottles of acid.

 

[Seadog]

I bought a scooter battery about 4 years ago. Acid in separate container.

 

[The_Yellow_Ardvark]

Is it a 12ah battery in the OP's post.

Any fire/intruder alarm supplier sell them and Screwfix as well.

All filled and ready.

 

[sako243]

Is it a 12ah battery in the OP's post.

Any fire/intruder alarm supplier sell them and Screwfix as well.

All filled and ready.

It is a 12Ah but it's about half the price from the local tractor factors compared to Screwfix so can't really complain.