Apologies for the delay in getting sizes, just kept forgetting! Hopefully these are of some use to you for a general layout and size point if veiw
Back to front
Overall height
Gap at bottom
Rear height from top of gap
Setback before slope
Overall width
View from inside showing step up, no...
Could maybe invert the symbol so it's sitting proud at the back, print in clear resin and infill the back.
I have a resin printer and some clear resin, is horrible stinking stuff but if someone can make the STL I wouldn't mind trying. So long as there is an oil pressure, temp warning and battery...
Well done that man,1970's fiat 500 front cylinder is 22.2
https://www.onlinecarparts.co.uk/abs-7711298.html
Forgot cars had front drums, my first mini was twin leading shoe, and a death trap
Got a few places to contact now, thanks. The chap who runs a thwaites restoration site I contacted said it's an odd Italian axle on that machine, so started looking at Italian cylinders, thankfully parts in motion has some diagrams-
Trw bwd103 from a fiat 126, very very close except bore, but...
Cheers, that's narrowed my search with Bendix,
If I could just find the seals that would be fine, bores look good and bleed nipples weren't seized! Probably because they were encased in concrete. But seals are brick hard, looking like I might have to try extract one for comparison but it might...
Have a slight conundrum trying to find either seals or a replacement wheel cylinder for a dumper, is a thwaites sprite 750 for what it's worth. Thought I was into a winner with one website but is discontinued and he didn't have anything suitable.
I can modify the backplate if holes are needing...
Hi, do you have any pictures of yours and I can see what bits your after? Think the syncro was pretty much the same but with a big lever on the top to adjust the pulley?
I had an 07 focus cmax and sure it had some weird electric hydraulic steering? Hydraulic rack with an electric pump, could hear the pump wind down when you turned the ignition off. Could always double check there isn't a fluid reservoir?
Think the cmax changed in 07 - 08 from focus cmax to just...
i brushed on when i did the underside, was a pain and took forever! ended up buying one of these things - https://www.ebay.co.uk/itm/315019847116?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=lkpnytb_tna&sssrc=2047675&ssuid=IUoauAtKSrO&widget_ver=artemis&media=COPY
Pressure pot sprayer, for...
Just had my little Kubota engine rebored, looks like it's a liner engine but was advised it's easier and cheaper to just take 0.5 off if it's not had anything horrible done to it. £216 with pistons, not too bad I think.
Proper old machine shop with folk who have done it for years, but moved with...
Got mine running today, steamy, is a 75 one so just ground pin 3 and fuel pump from pin 6. Using the wrong fuel pump and the fuel tank is a spray can cap, but proved it so it's worth servicing :D
That's a very good point about suction, I could poke a few holes on the bottom easy enough and see if that helps, will also look at light off delay times. Still new to resin stuff, got to think a different way to fdm
https://www.75ztcommunity.co.uk/webasto-fbh-useful-info-t9734.html
Might find this useful regarding the 98570b and pins, even though you swapped the board's
interesting, i have just bought a rover 75 thermotop, the one that doesn't need a can bus signal. going to try retrofit to my Freelander as i like not being cold! can buy brand new kits from aliexpress for about £200 with the remote and stuff, picked up my untested one for 70 which seems...
I'm having a spot if bother with some odd banding on a print I have been trying to perfect, always in the same spot but varies in size depending on orientation
Hard to see but angled ones were tilted, straight faults printed flat, thin flat one with impossible to remove supports was printed...