well since i had a little play with it seem to be working fine now :D
I had to spin the cap around to see the label and it must of been a dirty connection or something so im going to take it all to bits and cleen it all up and see
but cheers for the help any way guys i know what to get...
cool cheers for the help man :D
these to are the closets i can find witch do you think i should go for?
http://www.ebay.co.uk/itm/80uf-100uf-Motor-Start-Capacitor-250v-80mfd-100mfd-/260717465214?pt=UK_BOI_Electrical_Components_Supplies_ET&hash=item3cb3f8ce7e...
hi my compressor has always been a pig to get started and i have just been reading this thread
http://www.mig-welding.co.uk/forum/showthread.php?t=33098&page=2
and i think its the cap that's gone on mine so im going to order one as there only about a 10er but im unsure what one to order...
you do it with a baseball bat just roll it between the tyre and the arch get a mate to hold it and drive the car forward and backwards theres loads of vids of people doing it on you tube i did mine with a old small disposible co2 bottel works real well
yer i got a mate of mine to tig at his work 2day looks sweet naw i think its my welleder the wire speed seems to be playing up on it but i have got another one so im just going to use that from naw on hears some pics of it and them all finished :-)
i got a manifold with some cracks in...
it might be to slow i think the wire fead is runing slower then normel i will try my other mig set some time this week see if i can get anying out of that one
dident relly have much time to play with it 2day but probley have a play with it on munday
cant get any penetration WHEN WELDING :ashamed:
i have got a wheel i need to repair hears a pic
i just tryed to do a line on a old alternator and it wasent haveing any of it just welleding up the end of the torch evey time. i cleen the earth and the area had a play with wire fead and...
o right yer i was thinking what the hells he on about hehe
so where about in bedfordshire are you and what do you do ?
im in bedford full time bum atm lost my job trying to kit the garage out a bit and get some prodjects done
the welder works real well real happy with that
still not tryed the compressor as its 110V need a trany for it its 10.2cfm i did find it on google cant rember whats all the spec was its a good one tho
what do you meen billj ( paint reservoir has exploded. ) its not got one its just got...
I went to get some wheels blasted and when i was there i saw there was a mig set just like mine but its a sealey one mine a re baged one called maypol 160. so i ask whats up with it as it was all in bits he sed the wire fead was all jumpy then i thought i have got spair moter for one of these...
the paint on the wheels is so stubborn blasting hardly even touches it pant striper just makes it feal like rubber and cant get it off with a wire brush
what i was thinking of geting it some water based paint striper and just mixing it with some more water so it would be 50/50 mix then dip...
i have a few sets of wheels i want to re paint but need to strip the old paint off
but most of them have been powder coated with about another 5 coats of paint on top so theres a lot to get off :(
i have tryed nitromors but you have to use about £15 worth of it on one wheel and it takes...
yer cant be assed to spend to much trying to recycle as much as possible in the garage been useing old work tops bits of wood ect for shelves that i have found
so i will probley just cut it with the grinder and a dust mask on
it just them panels on my garage have got steel rods in them allmost evey time i have put a shelf up ect i hit a steel bar its a pain in the ass i might just try cut the hole with a 9" grinder
what should i seal it with or should i just make a plate out of sheet for each side the and welled...
yer thats what i was thinking but the only problem been is my garage is one of the cheep concrete bolt up ones so it would be hard to cut a hole in
like this one but no as tall roof
http://www.leisurebuildings.com/acatalog/images/leofric/sussex.jpg