mosa seem to have a habit of doing this. i have one that did it, so dose a mate thev both just been used as a 240v genorator ever since had qutes to fix them but they were scary
im useing an hydralic oil cooler of a dead hydrovane, automotive engine oil cooler also work massive surface area for a small thing being a proper radiator ,
my personal oppinion with useing plumbing pipe now is if your going to use it use a pipe bender and have the runs almost...
a farmer would just tie some 6mm T+E and tie it up with bailer twine it would work .
if its low id personally use some armored or put it in something like black alkathene or conduit
the biggest issus with a frames are they wont go on most cars made in the last 15 years. undertray has to come off to get at the wishbones it often holds loads of plastic trim like arch liners off the wheels. then there is the frount bumper they have got lower it will probally hit the...
ive been running a lincon vantage 575 for a while now, it has cv mode
i have a suitcase feeder but dont use it , most of time i use a std remote wire feed with a transformer tek screwed to the back of it to sort the wire feed voltage issue out. its done a lot of work now but nothing much...
tbh theres lots of frames going up that arnt CE marked,
for makeing a shed frame say for myself if i didn't have a big mig i would seriously look at hireing one in, tho it depends how you value your time but stick welding is painfully slow imo, blast frams together with mig then recitify the...
sounds like i may have to go and have a look at clearview as they arnt that far away really. just been haveing a bit of a work out this evening how to do the lineing ect
engines have fancy bolts, well they do now. a lot of old stuff you had to retorque after so long running or after you'd got it hot. well you din't have to but the gaskets lasted a lot better for it
compressors arnt that fussy i normally just put them down firm with a 3/8 ratchet and that'll do if im feeling posh ill re nip them after a few running hours. tho that said i put the heads down on mine with the battery rattel gun and there are no head gaskets in it just a bit of rtv sealer...
i have a plan to test the heat output, ive grabbed every electric heater i can lay my grubby littel mits on, im not going to be abel to plug them all in but the plan is to drag the workshop genny down to run them and do an expriment.
how meany kw of electric heaters before im watching...
yes they are amazing things parents house has a charnwood that was fitted 20+ years ago that heats the whole house happily on its own unless it really really cold.
i think i'd like to do the chimeny right for a monster of a fire with back boiler then fit something in the 5-8kw range for the...
well reading some of these replys i may go smaller than i was going to.
intresting sugestions about a back boiler it keeps going round in my mind, the house was built when oil was cheep, the fireplace was built as more of a feature, the central heating is oil fired and we dont use...
i hear what your saying tho what i hear is quite a few woodburners are "derated " to 5 kw for the regs. so they apprently often do more also the room is massive and this place is stone built its allways cold, just measured it as 5m x 8m x 2.5m and i think given half a chance all the...
thats good so id get away with some old vintage thing as long as i know what it is and what its rated at :) yes ideally summer would have been ideal but summer went all wrong this year, i threatened to do this last year but stuff got in the way, i'm going to have to sort out lining...
yes as long as you can get them out, ive had some injectors that just wont move and ive even resorted to welding things to the injectors and making frames to pull on them, then starting the engine up. think theres still a transit head under the bench where we gave up and swaped the head...
ive been and uttery confused myself again, currenty we have an open fire place that we dont use as it uses an incredible amount of wood to do not a lot,
putting a liner in the chimney dosent seem like to much hard work, but the sticking point for me is going to be the wood burner, its a...
for my own stuff i did most of the welding went away, unfortunatly occasionaly at work i end up haveing to weld some farmers truck back together garanteeded way to ruin the week