I've got one with exactly the same trouble , i think it may be pcb failure? but im no expert. i can get the gas solenoid to work but not the wire feed motor , i hard wired my motor to a 12v battery charger and it spins very well under power , so my motor is o.k. you can do the same to your motor...
if its not getting a spark it may have a thin layer of rust built up with standing idle . remove the coil and Emmery ( wet and dry ) the faces that fit above the flywheel . when refitting i use a couple of lengths of insulation tape on the clean fly wheel then fit the coil , the tape will...
i think its illegal to Carry a folding blade over 3 inches . its silly realy as you can kill a person with almost anything if you wanted . i knitting needle , a boot lace . if a person is intent on harming another person , then there going to harm them . you cant carry a knife but the government...
you could always hire an inverter for the day , they may even drop it off at the address . don't know what it would cost , though f someone can afford a commission sculpture in there garden then they can afford the price of a hired welder .
the only arc welders i have used were oil cooled . pickhill , oxford, quasiarc . all very good welders just heavy to move about the quasi i had was 300 amp and took towo people to push about . oxford do a nice 110 amp welder i would still opt for a decent mig the weld is a lot cleaner and they...
esab , murex, boc, lincoln, eland, portamig, kamanchi, oerlikon, miller usa , kemppi , multi weld , britweld, arctech , migatronic , nbc, nexus , hobart usa . all top brands . i would advise you to buy a 180 - 200 amp as they will do car body work up to 6mm thick avoid SIP , clarke , cebora ...
a good second hand quality welder with copper transformer and decent wire feed and euro torch . you could get a cebora or a clarke as they do a nice weld ,they just not built with quality components and have a shelf life . you don't want a gasless mig . snapon are just a cebora with an expensive...
it just isnt getting enough power , what power variable speed transistor should be fitted ? this one says 10 va i think not sure of the amps though . . i have emailed the circuit board man in Yorkshire about getting it refurb but i have had no reply yet . its no good sending it unless he has...
i thought of just putting simple basic board on . the problem with this board is i don't know if parts have been replaced with compatible parts by the last owner . this is how i bought it , I've never used it yet . i may try one last attempt and replace the wire feed control . the low voltage...
right i fitted a higher amp bridge rectifier and found that thew last person to repair it had actually fitted the dc out wires to the ac in on the rectifier . any way with the higher amp rectifier and the wires now soldered to the new rectifier the motor is still short on power , it has improved...
what do you mean ? taxes must be paid and even more so now to pay for private banks bad investment . yes i know we didnt get a say in the matter and were forced into it and i know we joined the European union without the public having a say in the matter but think your self lucky we are still a...
i would do away with the block paving and put a pit in , think of the money you will save on blocks . and you can fill it with water and sling the kids in in summer . on a more serious note you can get an ant repellent that works off a battery and sends off a high frequency . who knows it might...
id be upset if id did not pass , its not the most beautiful in the world but its safety we are concerned about , not cosmetics . I've been out with some plain ugly birds but they were as safe as houses if you know what i mean ? pmsl . i wouldn't under seal it until after the mot though as the...
well looking at the spec of your welder its a 180 amp out put max and i would be very surprised if it didn't take a 15 kg reel of wire . its more than likely a misprint in the book . if you think the stub axle can hold the weight of a 15 kg then try it , it wont hurt the transformer . has it got...
hi whats the maximum amps output ? .8 wire is the best all round wire if your welding car body up to 6mm plate . i don't like the sound of the 1kg are you sure it didnt say 15 kg ? im assuming its a 200 amp welder mind going by the model number , though new welders seam to use anything these days .
don't count on coming out of the recession , the usa are starting to admit they are in a depression and are expecting the market to drop this back end . also the u.k main stream news said our government is expecting a double dip recession . the only reason the market looks better is because we...