well if tryed a few diffrent things out now when i turn on nout happen i pull triger and still nout i tourched the points on the realy with a screwdriver to make them shut and the transformer starts i pull trigger motor goes for a sec and transformer dies it looks as the realy opens when i pull...
no thats how my diagram is when i pulled it apart and is right the only thing i can see that would be broke is that round black thing what is it and whats it do
got no wat to take photo iys wired right as iv had it worken were the mains go R is earth S is live Tgoes to high low switch wite goes to red on motor red to rectifier blue and black to tourch triger as my themal protector is in diffrent place and this is only way that worked untill wire come...
no thats why i put the pcb board in it was worken fine the motor and tourch went live when i pulled the trigger but i knocked the mig and the live 240v wire or the high low wire from the transformer hit the heat sheild on the board and the mig wire from gun was hiting caseen so 240v went through...
thats right the tourch is live and its a sip migmate some how the tourch is live all the time and when i pull the trigger the motor runs and the realy switches off and back on again as it should do but when i let go of trigger the tourch is still live something on the board is operaten the realy...
no as i said at start the main wire come off the switch and 240v went into the heat sheild on the board and the welding wire was also tuching the caseing on the welder as well as in the torch it welded to the case and snaped as well as house trip switch triggering
i dont mean the one in the red circial the square red box but on mine its a red one the realay in the red circial open and shuts ok its colesen when i swich the power on instead of when i pull the trigger
the feed motor runs fine when you pull yhe triger but the transformer is on all the time insted of when you pull the triger the main 240 wire that goes to the switch high low come off and hit the heat shield on the pcb board any one no what compolent would have gone to ,make it live all the time...
I Found This Add For A Pub Co2 Bottle For £15 Plus £22.50 For First Bottle If You Havent Got One £20 For A New Reg And £11 For 5kg Wire About 3 Miles From Motorway Near Brighhouse the numbers is 01484401540.iv got it today its got about 6.35 kg of gas in it 14-15lbs the bottle emty is16.1kg with...
any one got a sip 80 or 100 wire diagram as i got my mig new but had no pcb board so i got a old 150 with bust transformer and robbed the pcb but dont no were wires go thanks
hi got a sip 150 migmate i can not get a spark off the wire and the wire will not come out of the end when i pull trigger but if i tuch it on to the metal the wire comes out but not welding do you think its the transformer i tried to test it but nout has anyone got a new or second hand one if...
sip wire
no iv got a sip 80 and the lids on the top and when you open it up yousee the rollers at the front and the bar at the back when i put the large roll in it hits off the back of the welder and the bolt no were nere the middle to srew it in i was going to move the hold towards the front...
i got a 5 kg spool of wire but its to big for my welder i got it from liverpool way and im up at gateshead newcastle upon tyne is there a way to put it onto the small spools or if anyone close to me would like to swap it for 3or4 small one let me no and pm to come to arangement thanks.
i need a reg co2 to argon convertor as my co2 reg has the nut end on to screw ont o the threds on the outside of the pub bottle valve but i got a pub co2/nitrogen bottle full with just co2 in and the valve has got the threads onthe inside any ony got a spare convertor spare or cheep let me no...