Unlikely as it sounds to be believable, I've personally been in this situation, so yes, irrespective of legality to be parked they are removed.
My taxed/insured/mot'd renault master van was parked outside my house in sussex, we'd loaded some of our furniture into it and parked it up and the...
You have to look and watch for a l00 spindle, I've only ever seen mine for sale and that was a clearance item from G&M. When I bought it, I didnt know if it would be transferable, and I was lucky to have a surface grinder to reduce the spline od to one that worked & even after all that I've had...
Golden rule 2 of landrover ownership. Don't rely on whats there being done correctly by someone else in the past...
I had my shoes on and off mine for a entire day after copying exactly how they were when I first came to them before I twigged that the entire shoe sets had been swapped left and...
heh, on the 101 it has twin leading shoe drums up front, so two slaves. Inexplicably at design time someone thought it was a good idea to put the bleed nipple on the lowest point of the lower cylinder and feed it from the upper cylinder. And people wonder why 101 owners dream of zeus front disc...
Lorry brakes are a different thing in they dont use hydraulics. They have a S shaped cam and a shaft out the drum backplate, and this is pushed by a slack adjuster linking it to a air pod, assuming you mean hgv. Then servicing becomes take the drum off, wash it all off with a kettle of water so...
Here you go, 3 shots, first from underneath inside from roughly by the diff, showing the main rails attaching to the xmember.
Here is where the chassis rails line up with in relation to the seats/arches etc. Its inboard of the seat tub edges so plausible you could drill out the rivets and lift...
Here, this is a seller selling the "rear body" assembly that would have to come off that isnt designed to slide off in seconds to lift with a helicopter. It gives a good idea of what it actually consists of in terms of weight (remember this is mostly birmabright ally). The open cutaway end is...
If its a GS, then "body off" isnt quite as dramatic as it sounds, the tailgate and sides slide off on pins, so the body is the rear wheel arches, and the body pillars with the hoodsticks each being secured with a single bolt then pushed onto a stub so they just lift off. You dont need to touch...
If anyone knows what the top tool is also, please pipe up also, its sat in the drawer with the forked tool and I've never quite figured out what its for.
Next time you do it, or to reassemble without grief, get hold of one of the old lucas girling brake shoe spanners or make something similar.
Its the bottom one in this shot, the fork has a section cut out in the middle of it so the forks straddle the centre rib of the shoe. I can get a better...
Also if you see a ceramic chip forge for cheap enough, they also work quite well. I have often noticed them sell untested for less than the valves and a nozzle to make your own would cost alone s/h. Here's mine running on a bottle gas of butane warming up, it has its own air pump in the base and...
I'd just buy a good used ramp myself. In fact I did, a 4t fog for 500e including a roll along air jack on a moveable bridge too.
I spotted it in the free ads, and whipped round there and took it down and transported it in my sprinter by taking the front passenger seats out and sliding it right...
Looks like 4 highlifts on a four post lift frame, doesn't that mean you'd have to walk round each corner for each notch? Same to descend.. So elevate inch by inch...
That'd get old really quick.
Ive had my lathe tooling on a board behind the machine for 15 years now. Never once have I been dumb enough to even be tempted to reach across and lift a chuck off its position to change on a machine already set up for doing a job. Taper tooling for the tailstock yes, who doesnt hot swap that...
My manual milling machine has no quill, the arno is a universal with a bevel gear inside the head and takes iso40 so I think they went for bulk and rigidity over a quill there, but what it does have is a powered knee so it cranks itself. A few extra long bits of tooling take care of those odd...
As cobbler, the heavy volume of consuming tools will see the difference, but not all. My impact gun runs better on the single fitting I have with a higher volume capability but the rest of the workshop I just have on pcl. The gun & blasters work better on the high flowing connection but nothing...
I've always been curious about using a cheap old horizontal as a ring roller setup. Two concave wheels with bearings in supports on the table and a 3rd on the arbor and the gearing dropped. I've never been brave enough/had enough time to tinker to subject my unversal to that sort of treatment...
Plug the egress and exit holes at night when theyre out hunting if you can, then they move on to the next nearest place not being able to get back in the door.
I was fascinated by the ft high perfect cone of butterflies and moths they left upstairs while eating in their fav spot in one building...