Hi mate
If you need any repair panels etc for your MG project then give me a shout.
Im a supplier for Hadrian Motor Body Panels :D:D:D
cheeRS
Chris
PRP - Passion Restoration Products
Good Answer Rusty :clapping::clapping::clapping:
Im a distributor for Hadrian Body Panels and most of the sills i have sold have small lips recessed out on the lip edge where its spot welded to the inner sill and if they are not present then i usually drill into the inner rear arch 10-12mm...
Hi Andrew
Dont be drilling holes in the sill mate :(:( recipe for disaster.
If you look on the inner sill you will see cavity holes, there behind some sound deadening sticky pad but they will be there. Once you have located them, this is where you feed the waxoil tube though and pump the...
Think yourself lucky matey
This is my latest project
Floor needs replaced
Non existent battery tray
Get some finished pics up when new sills are on and dont forget to inject some waxoil into those sills :D
cheers
Chris
Hi mate.
You can also take your casings to a blast shop and they
will thoroughly de-grease it in there hot 80 degree tanks and they can then glass bead it.
I have just had my aluminium ford gearbox casing glass beaded and it is like brand new.
I too have a 2nd dishwasher as its a god...
Im doing something similar but ive designed a frame for a car roll over system. Its an A frame which will house a pivot and machined disk with holes in so that i can lock the car at different angles and then this is mounted to the car via the front and rear bumper mounts
A-Frame
Bumper...
Hi matey.
Ive just set up my account with BOC as they were far far cheaper than Air Products
Air Products
Fermaxx7 X30s
£18.80 for bottle
£0.36 bottle rental per day or £113.01 yearly
Delivery £39.90
Collection £14.82
BOC
Argoshield Light
X = £29.37 - Bottle rental = £5.58 per...
Hi all
Im after a bit of advice on welding in my new sills. Iv
put some pics below so you can make sense of what im on about.
Ive cut the old sills off but ive been told that when i come to butt weld in the new one it will distort like mad. Is there any other way of doing it without it...
As above, send Steve (Weldequip) a private mail and he will sort you out with everything you need matey. His service is top notch and cheaper than anywhere else.
cheeRS
Chris
Link to Steve
http://www.mig-welding.co.uk/forum/member.php?u=461
Whats your plans for the car mate. If your repairing to sell it then patch her up but if its a keeper then i would cut the lot out and replave the floor pans, give inside floor a coat of yellow, the stone chip underneath if you want to the job properly.
Hadrian still do repair panels for the...
Because only one bottle had a label on. The maroon coloured one had nothing whatsoever to indicate what was in it. + i know diddly squat about gas apart from if you smell it then ring the free phone number on the back of the van :laughing::laughing::laughing:
Was talking to my welder mate yesterday about getting me some argoshield light for my new welder and he told me to have deep pockets as the price of gas has gone through the roof and companies are now charging daily rental on bottles??? Is this true??? Hope not as im doing a car resto project...
As im currently restoring my car ive tried them all.
The ones from Machine Mart are a total waste of time.
The 1st one i bought it done around 15 spot welds before all the teeth snapped off :vsad::vsad:
So took it back, thinking it was a faulty, got another one and tried again, this time...
LOL
Mmmmm that may take a bit more than just a panel :welder:
Mine aint bad really but with it being a concours car i cant just patch it up here and there as i will lose points.
Also its amazing how much a bodykit hides :(:(:(